Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM J

1KR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the ignition switch is turned to ON, the MIL should be illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A373204E69
1.26,0.885 1.875,1.083 0.615,0.198 10 false CANH 1.292,1.594 1.906,1.792 0.615,0.198 10 false CANL 2.833,0.875 3.448,1.073 0.615,0.198 10 false CA3H 5.51,1.573 6.125,1.771 0.615,0.198 10 false CANL 5.51,0.865 6.125,1.063 0.615,0.198 10 false CANH 2.844,1.573 3.458,1.771 0.615,0.198 10 false CA3L 3.927,0.875 4.542,1.073 0.615,0.198 10 false CA4H 3.948,1.583 4.563,1.781 0.615,0.198 10 false CA4L 0.927,3.219 3.042,3.51 2.115,0.292 10 false : CAN Communication Line 2.896,2.25 4.438,2.5 1.542,0.25 10 false Network Gateway ECU 0.083,2.25 2.021,2.573 1.938,0.323 10 false Combination Meter Assembly 6.073,2.26 6.583,2.542 0.51,0.281 10 false ECM 6.094,2.094 6.708,2.292 0.615,0.198 10 false A55 2.906,2.094 3.521,2.292 0.615,0.198 10 false H40 0.094,2.094 0.708,2.292 0.615,0.198 10 false H6 1.76,0.708 2.375,0.906 0.615,0.198 10 false 9 1.729,1.417 2.344,1.615 0.615,0.198 10 false 25 2.604,0.708 3.219,0.906 0.615,0.198 10 false 30 2.604,1.417 3.219,1.615 0.615,0.198 10 false 29 4.385,0.698 5,0.896 0.615,0.198 10 false 26 4.385,1.417 5,1.615 0.615,0.198 10 false 25 5.26,0.698 5.875,0.896 0.615,0.198 10 false 26 5.271,1.396 5.885,1.594 0.615,0.198 10 false 25

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
MIL Condition Proceed to
Illuminates → Turns off Ignition switch ON → engine is started A
Other than above - B



A

B

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Perform the Health Check using the GTS.


b.

Check if any DTCs have been detected. Note down any DTCs.


Result:
Result Proceed to
DTCs are not output A
Any DTCs is output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.



A

3.PERFORM ACTIVE TEST USING GTS

B

REPAIR CIRCUIT INDICATED BY OUTPUT

3.PERFORM ACTIVE TEST USING GTS
a.

Check the status of the MIL while performing the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Warning
50004 409 64
Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY