Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P01052A  Manifold Absolute Pressure / Barometric Pressure Sensor Signal Stuck in Range  


DESCRIPTION

A207508E12
0.083,0.115 0.854,0.344 0.771,0.229 10 false Voltage (V) 0.26,0.625 0.51,0.792 0.25,0.167 10 false 4.2 0.26,0.896 0.531,1.073 0.271,0.177 10 false 3.6 0.26,1.365 0.521,1.583 0.26,0.219 10 false 2.4 0.25,1.771 0.49,1.948 0.24,0.177 10 false 1.2 0.26,1.979 0.521,2.177 0.26,0.198 10 false 1.0 1.115,2.448 1.604,2.604 0.49,0.156 10 false 19.988 1.604,2.458 2.104,2.667 0.5,0.208 10 false 59.995 2.115,2.458 2.615,2.635 0.5,0.177 10 false 99.992 2.573,2.448 3.115,2.646 0.542,0.198 10 false 119.990 3.094,2.208 3.375,2.406 0.281,0.198 10 false kPa 0.979,3.146 1.271,3.354 0.292,0.208 10 false 100 1.146,2.948 1.438,3.125 0.292,0.177 10 false 150 1.719,2.948 2,3.125 0.281,0.177 10 false 450 2.323,2.948 2.594,3.146 0.271,0.198 10 false 750 2.667,2.948 2.948,3.104 0.281,0.156 10 false 900 0.875,2.646 1.365,2.802 0.49,0.156 10 false 13.332 2.875,3.094 3.344,3.281 0.469,0.188 10 false mmHg

By a built-in sensor unit, the manifold absolute pressure sensor (intake manifold) detects the intake manifold pressure as a voltage. The ECM then determines the basic injection duration and basic ignition advance angle based on this voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P01052A Manifold Absolute Pressure / Barometric Pressure Sensor Signal Stuck in Range One of the following conditions is met (1 trip detection logic):
·

Difference between the intake manifold pressures before and after the engine start remains 50 kPa or less for 2 seconds or more.

·

The pressure detected by the sensor is not within the standard range calculated from the engine speed and throttle opening angle.

·

The sensor is frozen.


·

Intake manifold

·

Intake system


Comes on DTC stored Engine B

WIRING DIAGRAM

A322487E07
5.552,2.333 6.146,2.583 0.594,0.25 10 false ECM 0.427,2.292 3.938,2.625 3.51,0.333 10 false Manifold Absolute Pressure Sensor (Intake Manifold) 1.75,0.719 2.01,0.906 0.26,0.188 10 false VC 1.708,1.219 2,1.406 0.292,0.188 10 false PIM 1.781,1.708 1.99,1.885 0.208,0.177 10 false E2 4.917,1.615 5.292,1.792 0.375,0.177 10 false E21 4.917,1.135 5.313,1.344 0.396,0.208 10 false PIM 4.917,0.656 5.26,0.813 0.344,0.156 10 false VC2 5.177,2.333 5.5,2.542 0.323,0.208 10 false D50 0.427,2.115 0.76,2.292 0.333,0.177 10 false D21 2.063,0.656 2.25,0.833 0.188,0.177 10 false 3 2.063,1.146 2.167,1.333 0.104,0.188 10 false 1 2.063,1.615 2.25,1.833 0.188,0.219 10 false 2 4.573,1.615 4.844,1.854 0.271,0.24 10 false 127 4.563,1.135 4.875,1.333 0.313,0.198 10 false 129 4.635,0.656 4.906,0.833 0.271,0.177 10 false 95 5.698,0.396 6.042,0.552 0.344,0.156 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P01052A)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P01052A is output A
P01052A and other DTCs are output B


HINT:

If any DTCs other than P01052A is output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

GO TO DTC CHART

2.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Read the Intake Manifold Absolute Pressure value at ignition switch ON.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50003 372 211,385,205
Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 80 and 110 kPa A
None of the above conditions are met B




A

3.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

3.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Read the Intake Manifold Absolute Pressure value at idling.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50003 372 211,385,205
Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 29 and 37 kPa A
None of the above conditions are met B



Post-procedure1

d.

None.



A

4.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

5.CHECK INTAKE SYSTEM
4.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Read the Intake Manifold Absolute Pressure value at 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50003 372 211,385,205
Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 22 and 50 kPa A
None of the above conditions are met B



Post-procedure1

d.

None.



A

B

5.CHECK INTAKE SYSTEM
5.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

HINT:

Click hereEngine / Hybrid System>1KR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION


OK:

No leaks in intake system.



b.

Check the intake manifold.

OK:

The intake manifold is not cracked.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE INTAKE SYSTEM