Home › Engine / Hybrid System › 1KR-FE (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2020.07
RM36W0E _51 Engine / Hybrid System _091036 1KR-FE INTAKE / EXHAUST _0431304 INTAKE MANIFOLD A

1KR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55815E 2.REMOVE NO. 1 FRONT VENTILATOR SEAL (for LHD)

Hide 55815E 3.REMOVE NO. 1 FRONT VENTILATOR SEAL (for RHD)

Hide 55735A 4.REMOVE WATER GUARD PLATE LH (for LHD)

Hide 55735A 5.REMOVE WATER GUARD PLATE LH (for RHD)

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 22030 8.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 9.DISCONNECT VACUUM HOSE ASSEMBLY

a.
A468511C01
1.25,1 1.375,0.823 false 2.167,1 2.031,0.823 false 1.115,1.01 1.427,1.167 0.313,0.156 10 false *a 2.135,1.01 2.448,1.167 0.313,0.156 10 false *a
*a Retainer
V100135

Pinch
V100136

Pull


Pinch the retainer of the vacuum hose assembly connector, and then pull the vacuum hose assembly connector off of the intake manifold.

NOTICE:

Be sure to disconnect the vacuum hose assembly connector by hand.



b.

Disengage the clamp to disconnect the vacuum hose assembly from the vacuum hose clamp.


c.

for RHD:

i.
A425107

Disengage the clamp to disconnect the vacuum hose assembly from the vacuum hose clamp.



Hide 23827A 10.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE

a.
A468512C02
1.292,1.094 1.646,0.833 true 1.844,1.708 2.135,1.438 true 1.688,0.75 1.896,0.927 0.208,0.177 10 true *2 1.594,1.708 1.802,1.896 0.208,0.188 10 true *1
*1 No. 1 Water By-pass Hose
*2 No. 2 Water By-pass Hose


Disengage the 4 clamps to disconnect the No. 1 water by-pass hose and No. 2 water by-pass hose from the intake manifold.


b.
A468513

Slide the hose clip and disconnect the No. 2 fuel vapor feed hose from the intake manifold.


Hide 17650G 11.REMOVE PURGE VALVE (PURGE VSV)

Hide 25601 12.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 17111 13.REMOVE INTAKE MANIFOLD

a.
A468514

Disengage the clamp to disconnect the fuel tube sub-assembly from the fuel hose clamp.


b.
A468515

Disconnect the connector.


c.

Disengage the 3 clamps to disconnect the wire harness from the intake manifold and wire harness clamp bracket.


d.
A468516C01
1.885,0.76 2.229,0.948 true 0.802,1.469 1.135,1.229 true 1.177,1.125 1.385,1.302 0.208,0.177 10 true *2 1.635,0.646 1.844,0.833 0.208,0.188 10 true *1
*1 Wire Harness Clamp Bracket
*2 Fuel Hose Bracket


Remove the bolt and wire harness clamp bracket from the intake manifold.


e.

Remove the bolt and fuel hose bracket from the intake manifold.


f.
A468517

Remove the 4 bolts and intake manifold from the cylinder head sub-assembly.


Hide 44783 14.REMOVE VACUUM HOSE CLAMP

a.

for LHD:

i.
A425114

Disengage the clamp to remove the vacuum hose clamp from the intake manifold.



b.

for RHD:

i.
A425115

Disengage the 2 clamps to remove the 2 vacuum hose clamps from the intake manifold.



Hide 17177 15.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A425116

Remove the No. 1 intake manifold to head gasket from the intake manifold.


Hide 16.REMOVE STUD BOLT

a.
A425122

Using an E6 "TORX" socket wrench, remove the 2 stud bolts.