Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P212012  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Battery  P212014  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open  P212512  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Battery  P212514  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open  


DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal sensor assembly and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and malfunctions of the accelerator position sensor.

In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal which indicates the actual accelerator pedal opening angle and is used for engine control, and the VPA2 is a signal which indicates the information about the opening angle and is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.

HINT:
·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is a non-contact type.



A257314E14
0.885,2.833 0.49,3.323 false 1.063,3.177 1.26,3.865 false 0.833,1.927 1.021,2.552 false 1.396,1.49 0.958,2.25 false 4.146,3.135 4.354,3.135 false 4.146,2.927 4.354,2.927 false 4.333,2.031 4.146,1.958 false 4.323,2.208 4.135,2.177 false 4.333,2.26 4.146,2.406 false 4.344,2.417 4.167,2.625 false 4.333,1.75 3.813,0.844 false 2.042,1.75 2.479,2 0.438,0.25 10 false VPA 2.042,2.073 2.365,2.344 0.323,0.271 10 false EPA 2.042,2.396 2.49,2.698 0.448,0.302 10 false VCPA 2.042,2.688 2.448,2.948 0.406,0.26 10 false VPA2 2.063,3.01 2.51,3.208 0.448,0.198 10 false EPA2 2.052,3.333 2.542,3.583 0.49,0.25 10 false VCP2 0.125,1.073 1.25,1.49 1.125,0.417 10 false Accelerator Pedal Position Sensor 0.323,3.365 0.896,3.573 0.573,0.208 10 false IC No. 2 1.052,3.865 1.583,4.125 0.531,0.26 10 false Magnet 0.333,1.74 0.885,1.948 0.552,0.208 10 false IC No. 1 1.448,1.354 1.99,1.615 0.542,0.26 10 false Magnet 2.708,3.771 3.063,4.031 0.354,0.26 10 false ECM 4.302,3.521 4.396,3.667 0.094,0.146 10 false 0 5.833,3.583 6.177,3.781 0.344,0.198 10 false 12.4 4.74,3.563 5.708,3.823 0.969,0.26 10 false Usable Range 5.844,1.563 6.01,1.896 0.167,0.333 10 false *2 4.302,1.542 4.479,1.802 0.177,0.26 10 false *1 3.917,3.063 4.177,3.302 0.26,0.24 10 false 0.8 3.906,2.833 4.167,3.052 0.26,0.219 10 false 1.6 3.833,1.854 4.167,2.083 0.333,0.229 10 false 4.55 3.771,2.094 4.167,2.323 0.396,0.229 10 false 3.988 3.844,2.365 4.146,2.604 0.302,0.24 10 false 3.75 3.813,2.594 4.25,2.854 0.438,0.26 10 false 3.188 4.385,3.365 4.708,3.594 0.323,0.229 10 false 0.29 1.667,0.646 3.833,0.979 2.167,0.333 10 false Accelerator Pedal Position Sensor Output Voltage (V) 4.344,3.885 6.615,4.135 2.271,0.25 10 false Accelerator Pedal Turning Angle (°) 4.406,4.219 6.813,4.49 2.406,0.271 10 false *1: Accelerator Pedal Fully Released 4.406,4.469 6.823,4.802 2.417,0.333 10 false *2: Accelerator Pedal Fully Released 6.385,1.833 6.792,2.042 0.406,0.208 10 false VPA2 6.438,2.26 6.844,2.469 0.406,0.208 10 false VPA

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P212012 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Battery VPA is 3.9 V or more for 0.14 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in EPA circuit

·

Short in VCPA circuit

·

ECM


Comes on DTC stored Engine A
P212014 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open VPA is 0.7 V or less for 0.14 seconds or more when VPA2 output indicates accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in VCPA circuit

·

VPA circuit open or ground short

·

ECM


Comes on DTC stored Engine A
P212512 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Battery VPA2 is 4.7 V or more for 0.14 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in EPA2 circuit

·

Short in VPA2 circuit

·

ECM


Comes on DTC stored Engine A
P212514 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open VPA2 is 1.5 V or less for 0.14 seconds or more when VPA output indicates accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in VCP2 circuit

·

VPA2 circuit open or ground short

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

A322497E05
1.75,0.635 2.229,0.958 0.479,0.323 10 false VPA 1.75,1.052 2.229,1.375 0.479,0.323 10 false EPA 1.656,1.469 2.135,1.792 0.479,0.323 10 false VCPA 1.677,1.885 2.156,2.208 0.479,0.323 10 false VPA2 1.677,2.292 2.156,2.615 0.479,0.323 10 false EPA2 1.677,2.719 2.156,3.042 0.479,0.323 10 false VCP2 2.146,0.521 2.333,0.708 0.188,0.188 10 false 6 2.146,0.938 2.333,1.125 0.188,0.188 10 false 5 2.146,1.354 2.333,1.542 0.188,0.188 10 false 4 2.146,1.771 2.333,1.958 0.188,0.188 10 false 3 2.146,2.188 2.333,2.375 0.188,0.188 10 false 2 2.146,2.604 2.333,2.792 0.188,0.188 10 false 1 5.427,0.521 5.906,0.844 0.479,0.323 10 false VPA 5.427,0.938 5.906,1.26 0.479,0.323 10 false EPA 5.427,1.354 5.906,1.677 0.479,0.323 10 false VCPA 5.427,1.771 5.906,2.094 0.479,0.323 10 false VPA2 5.427,2.188 5.906,2.51 0.479,0.323 10 false EPA2 5.427,2.604 5.906,2.927 0.479,0.323 10 false VCP2 5.177,0.521 5.365,0.708 0.188,0.188 10 false 47 5.177,0.938 5.365,1.125 0.188,0.188 10 false 48 5.177,1.354 5.365,1.542 0.188,0.188 10 false 49 5.167,1.771 5.354,1.958 0.188,0.188 10 false 50 5.177,2.188 5.365,2.375 0.188,0.188 10 false 51 5.177,2.604 5.365,2.792 0.188,0.188 10 false 52 5.813,3.313 6.292,3.635 0.479,0.323 10 false ECM 5.813,3.125 6.469,3.313 0.656,0.188 10 false A55 0.292,3.26 2.604,3.583 2.313,0.323 10 false Accelerator Pedal Sensor Assembly 0.292,3.104 0.948,3.292 0.656,0.188 10 false A62

CONFIRMATION DRIVING PATTERN

These DTCs are detected when the ignition switch is ON or engine running.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

If any DTCs related to the crankshaft position sensor, throttle position sensor, accelerator pedal sensor assembly, manifold absolute pressure sensor and camshaft position sensor are output simultaneously, inspect the VC circuit of each component.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the ECM connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-49 (VCPA) - A62-4 (VCPA) Always Below 1 Ω
A55-47 (VPA) - A62-6 (VPA) Always Below 1 Ω
A55-48 (EPA) - A62-5 (EPA) Always Below 1 Ω
A55-52 (VCP2) - A62-1 (VCP2) Always Below 1 Ω
A55-50 (VPA2) - A62-3 (VPA2) Always Below 1 Ω
A55-51 (EPA2) - A62-2 (EPA2) Always Below 1 Ω
A55-49 (VCPA) or A62-4 (VCPA) - Body ground Always 10 kΩ or higher
A55-47 (VPA) or A62-6 (VPA) - Body ground Always 10 kΩ or higher
A55-48 (EPA) or A62-5 (EPA) - Body ground Always 10 kΩ or higher
A55-52 (VCP2) or A62-1 (VCP2) - Body ground Always 10 kΩ or higher
A55-50 (VPA2) or A62-3 (VPA2) - Body ground Always 10 kΩ or higher
A55-51 (EPA2) or A62-2 (EPA2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-1 (VCP2) - A62-2 (EPA2) Ignition switch ON 4.5 to 5.5 V
A62-4 (VCPA) - A62-5 (EPA) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG