The left side 1st seat far side squib circuit consists of the airbag sensor assembly and front seat center airbag assembly LH.
The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B18D513 | Left Side 1st Seat Far Side Squib (Left Side 1st Seat Center Airbag) Circuit Open | ·
The airbag sensor assembly detects an open in the left side 1st seat far side squib circuit for 2 seconds ·
Front seat center airbag assembly LH malfunction ·
Airbag sensor assembly malfunction |
·
Harness or connector ·
Front seat center airbag assembly LH ·
Airbag sensor assembly |
Comes on | Applies to check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
To perform the simulation method, select Check Mode with the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| Current B18D513 is output | A |
| History B18D513 is output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the simulation method by selecting Check Mode using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Pre-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Procedure1
Check that the connectors are properly connected to the front seat center airbag assembly LH and airbag sensor assembly.
The connectors are properly connected.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
| *A | for RHD |
| *B | for LHD |
| *1 | Front Seat Center Airbag Assembly LH |
| *2 | Airbag Sensor Assembly |
Disconnect the connectors from the front seat center airbag assembly LH and airbag sensor assembly.
Procedure1
Check that the terminals of the connectors are not deformed or damaged.
The terminals of the connectors are not deformed or damaged.
Check that the short springs of the activation prevention mechanism of the wire harness connector are not deformed or damaged.
The short springs are not deformed or damaged.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the airbag sensor assembly.
| *A | for RHD | *B | for LHD |
| *1 | Front Seat Center Airbag Assembly LH | *2 | Airbag Sensor Assembly |
| *3 | Wire Harness | - | - |
| *a | Front view of wire harness connector
(to Front Seat Center Airbag Assembly LH) |
- | - |
Connect the black wire side of SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the front seat center airbag assembly LH for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTC B18D513 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| B18D513 is not output | A |
| B18D513 is output | B |
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Disconnect SST from connector C.
A
B
Pre-procedure1
Disconnect the connector from the airbag sensor assembly.
| *A | for RHD | *B | for LHD |
| *1 | Front Seat Center Airbag Assembly LH | *2 | Airbag Sensor Assembly |
| *3 | Wire Harness | - | - |
| *a | Front view of wire harness connector
(to Front Seat Center Airbag Assembly LH) |
- | - |
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O112-2 (FFL+) - O112-1 (FFL-) | Always | Below 1 Ω |
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for RHD |
| *B | for LHD |
| *1 | Front Seat Center Airbag Assembly LH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the front seat center airbag assembly LH and airbag sensor assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
Check for DTCs.
Codes other than DTC B18D513 may be output at this time, but they are not related to this check.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| B18D513 is not output | A |
| B18D513 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Perform the simulation method by selecting Check Mode using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
Perform the simulation method while checking the Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
B