Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › 2020.07–2020.09
RM36W0E _55 Steering _087265 STEERING GEAR / LINKAGE _0417608 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front suspension crossmember sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedures are not Performed Link
Wheel alignment adjustment for HV Model TMC Made:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for HV Model TMMF Made:
1.

Perform "Reset Memory"

2.

Perform calibration (brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

PROCEDURE

Hide 51201 1.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 45253 2.REMOVE STEERING COLUMN HOLE COVER

a.

Remove the steering column hole cover from the steering link assembly.


Hide 3.REMOVE STEERING LINK ASSEMBLY

a.
B576182

Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 4.SECURE STEERING LINK ASSEMBLY

a.
B576183C01
1.792,0.885 2.208,0.552 false 1.031,1.458 1.479,1.104 true 2.75,1.552 3.01,1.75 0.26,0.198 10 false *a 2.24,0.469 2.698,0.667 0.458,0.198 10 false SST 0.833,1.375 1.052,1.563 0.219,0.188 10 false *a
*a Protective Tape


Using SST, secure the steering link assembly in a vise.

SST
09612-00012  

HINT:

Wrap SST with protective tape before use.



Hide 45047 5.REMOVE TIE ROD END SUB-ASSEMBLY LH

a.
C165553C05
1.292,1.021 1.292,1.521 1.292,1.521 1.823,1.521 false 1.438,1.021 1.438,1.521 false 1.865,1.458 2.208,1.719 0.344,0.26 10 false *a
*a Matchmark


Put matchmarks on the tie rod end sub-assembly LH and steering gear assembly.


b.

Remove the tie rod end sub-assembly LH and lock nut.


Hide 45046 6.REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.