Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2020.07–2020.09
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Backup Boost Converter Circuit  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU. The backup boost converter helps maintain the power source voltage when the engine is restarted by stop and start control.

This prevents various functions such as the audio and visual system from malfunctioning if the power source voltage drops due to the auxiliary battery voltage dropping when the engine is restarted by stop and start control.

If any DTCs are output, troubleshoot the DTCs first.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*: A semiconductor fuse self resets according to electric signal.

The backup boost converter supplies power to:
·

Meter / gauge system

·

Power steering system

·

Audio and visual system

·

Navigation system

·

Headup display system

·

Tire pressure warning system

·

Toyota Safety Sense

·

Air conditioning system (for Automatic Air Conditioning System)

·

Parking support brake system



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the engine stop and start ECU or electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

For wire harness and connector inspection procedures and precautions, refer to "General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE"


PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Determine the trouble area by referring to the table below.

Effect on Vehicle Trouble Area/Cause Fail-safe DTC Output Stop and start cancel indicator Symptom Proceed to
When the engine is restarted by stop and start control:
The following symptoms may occur
·

Audio and visual system is reset

·

The combination meter assembly fades out

·

The steering wheel feels heavy when the engine is restarted*


Backup boost converter internal malfunction
·

Internal power source malfunction

·

Internal power source overvoltage

·

Duty error

·

Communication cycle error


Stop and start control prohibited P323A00
P323AA2
P323B29
P323B38
Blinks Converter output voltage cannot be boosted when the engine is restarted A
Auxiliary battery voltage drop
Systems on the converter output side do not operate
B41 terminal: The tire pressure warning system will not operate
B42 terminal: The audio and visual system will not operate
B43 terminal: Both of the following will not operate
·

Navigation system

·

Headup display system


IG41 terminal: All of the following will not operate
·

Headup display system

·

Tire pressure warning system

·

Toyota Safety Sense

·

Air conditioning system

·

Toyota parking assist-sensor system


Overcurrent applied to an output terminal (output terminal relay circuit is shutoff) Stop and start control is prohibited
(Connected ECUs or sensors may detect power source malfunction DTCs)
P323A19 Blinks Systems do not operate as power supply from the converter is cut off A
Systems do not operate
(Due to converter input side malfunction)
IGR terminal: All of the following will not operate
·

Power steering system

·

Headup display system

·

Tire pressure warning system

·

Air conditioning system

·

Toyota Safety Sense

·

Parking support brake system


IGP terminal: The meter / gauge system will not operate
ACC terminal: The Audio and visual system will not operate
Converter input circuit malfunction
·

Open or short to GND in IGR circuit

·

Open or short to GND in IGP circuit

·

Open or short to GND in ACC circuit


Stop and start control prohibited - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
Systems on the converter output side do not operate (varies depending on the malfunctioning relay circuit the converter detected)
AC42 terminal: The audio and visual system will not operate
IG12 terminal: The meter / gauge system will not operate
IG31 terminal: The power steering system will not operate
IG41 terminal: All of the following will not operate
·

Headup display system

·

Tire pressure warning system

·

Air conditioning system

·

Toyota Safety Sense

·

Parking support brake system


B41 terminal: The tire pressure warning system will not operate
B42 terminal: The audio and visual system will not operate
B43 terminal: Both of the following will not operate
·

Navigation system

·

Headup display system


Malfunction in circuits the converter supplies power to
(between the converter and ECUs or sensors)
Related systems do not operate as the relay circuit in the converter is turned off - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
All of the following systems do not operate
·

Audio and visual system

·

Navigation system

·

Power steering system

·

Headup display system

·

Tire pressure warning system

·

Air conditioning system

·

Toyota Safety Sense

·

Parking support brake system

·

Meter / gauge system


·

Open in BBC fuse circuit

·

Short in converter circuit

·

Backup boost converter malfunction


Stop and start control prohibited P061519 Does not blink (Due to disabled meter / gauge system) All systems that the converter supplies power to do not operate (see circuit diagram) A
P30DF62
P30EF4B
P323A00
P323A16
P323AA2
P323B29
P323B38
The audio does not operate (until the ignition switch is turned off) Excessive audio volume Data List item "State of BBC" displays "BBC Overcurrent" while the circuit is protected The relay circuit in the converter is turned off to cut off power supply to the audio and visual system (navigation system) (Returns to normal when the ignition switch is turned off) - Does not blink If overcurrent is detected in the audio and visual system (navigation system), system operation is disabled while the ignition switch is ON (Returns to normal when the ignition switch is turned off) C
The external backup boost converter (eco run vehicle converter assembly) output side system does not operate
·

Navigation system

·

Audio and visual system


·

Open in BBC NO. 3 fuse circuit

·

Malfunction in circuits the converter supplies power to

·

External backup boost converter (eco run vehicle converter assembly) malfunction


- - Does not blink All systems that the converter supplies power to do not operate (see circuit diagram) D
·

The combination meter assembly cannot be turned off (short between IG12 and +B)

·

Communication error DTCs may be stored due to short between AC42 and +B


HINT:

Varies depending on the number of times an open occurs in the +B circuit


Converter circuit malfunction
·

Short between IG12 and +B

·

Short between AC42 and +B


- - Does not blink The converter cannot shut off the power source when the ignition switch is turned off B
·

Ignition switch cannot be turned off from ACC (short between ACC and +B)

·

Ignition switch cannot be turned off from ON (short between IGP or IGR and +B)


Engine stop and start ECU power source circuit malfunction
·

Short between ACC and +B

·

Short between IGP and +B

·

Short between IGR and +B


- - Does not blink
·

Ignition switch does not turn ACC

·

Ignition switch cannot be turned off


B

*: A DTC may be stored in the power steering system



Result:
Proceed to
A
B
C
D



A

B

2.CHECK HARNESS AND CONNECTOR (BIN1 AND BIN2 TERMINALS POWER SOURCE CIRCUIT)

C

6.CHECK AUDIO AND VISUAL SYSTEM

D

8.CHECK HARNESS AND CONNECTOR (BIN TERMINAL POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (BIN1 AND BIN2 TERMINALS POWER SOURCE CIRCUIT)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-1 (BIN2) - Body ground Always 9.5 to 14 V
A66-3 (BIN1) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGR, IGP AND ACC TERMINALS POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - AUXILIARY BATTERY)

3.CHECK HARNESS AND CONNECTOR (IGR, IGP AND ACC TERMINALS POWER SOURCE CIRCUIT)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Turn the ignition switch ACC.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H43-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H43-21 (IGR) - Body ground Ignition switch ON 9.5 to 14 V
H43-18 (IGP) - Body ground Ignition switch ON 9.5 to 14 V



f.

Turn the ignition switch to off.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H43-19 (ACC) - Body ground Ignition switch off 0 to 1 V
H43-21 (IGR) - Body ground Ignition switch off 0 to 1 V
H43-18 (IGP) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Door Control and Tire Pressure monitoring System Receiver Assembly (w/o Entry and Start System)
Tester Connection Condition Specified Condition
H43-2 (B41) - O33-7 (+B) Always Below 1 Ω
H43-3 (IG41) - O33-1 (IGR) Always Below 1 Ω
H43-2 (B41) - Body ground and other terminals Always 10 kΩ or higher
O33-7 (+B) - Body ground and other terminals Always 10 kΩ or higher
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher
O33-1 (IGR) - Body ground and other terminals Always 10 kΩ or higher

Door Control and Tire Pressure monitoring System Receiver Assembly (w/ Entry and Start System)
Tester Connection Condition Specified Condition
H43-2 (B41) - O34-7 (+B) Always Below 1 Ω
H43-3 (IG41) - O34-1 (IGR) Always Below 1 Ω
H43-2 (B41) - Body ground and other terminals Always 10 kΩ or higher
O33-7 (+B) - Body ground and other terminals Always 10 kΩ or higher
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher
O33-1 (IGR) - Body ground and other terminals Always 10 kΩ or higher

Radio and Display Receiver Assembly (w/ Radio Receiver)
Tester Connection Condition Specified Condition
H43-12 (B42) - H79-4 (+B1) Always Below 1 Ω
H43-24 (AC41) - H79-15 (ACC1) Always Below 1 Ω
H43-12 (B42) - Body ground and other terminals Always 10 kΩ or higher
H79-4 (+B1) - Body ground and other terminals Always 10 kΩ or higher
H43-26 (AC42) - Body ground and other terminals Always 10 kΩ or higher
H79-15 (ACC1) - Body ground and other terminals Always 10 kΩ or higher

Navigation ECU (w/ Navigation System)
Tester Connection Condition Specified Condition
H43-11 (B43) - H82-10 (+B) Always Below 1 Ω
H43-11 (B43) - Body ground and other terminals Always 10 kΩ or higher
H82-10 (+B) - Body ground and other terminals Always 10 kΩ or higher

Meter Mirror Sub-assembly (w/ Headup Display)
Tester Connection Condition Specified Condition
H43-11 (B43) - H61-2 (B) Always Below 1 Ω
H43-3 (IG41) - H61-1 (IG) Always Below 1 Ω
H43-11 (B43) - Body ground and other terminals Always 10 kΩ or higher
H61-2 (B) - Body ground and other terminals Always 10 kΩ or higher
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher
H61-1 (IG) - Body ground and other terminals Always 10 kΩ or higher

Combination Meter Assembly
Tester Connection Condition Specified Condition
H43-10 (IG12) - H6-38 (IG+) Always Below 1 Ω
H43-10 (IG12) - Body ground and other terminals Always 10 kΩ or higher
H6-38 (IG+) - Body ground and other terminals Always 10 kΩ or higher

Power Steering ECU with Motor Assembly
Tester Connection Condition Specified Condition
H43-23 (IG31) - H1-1 (IG) Always Below 1 Ω
H43-23 (IG31) - Body ground and other terminals Always 10 kΩ or higher
H1-1 (IG) - Body ground and other terminals Always 10 kΩ or higher

Air Conditioning Control Assembly (for Automatic Air Conditioning System)
Tester Connection Condition Specified Condition
H43-3 (IG41) - H31-9 (IG+) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher
H31-9 (IG+) - Body ground and other terminals Always 10 kΩ or higher

Millimeter Wave Radar Sensor Assembly (w/ Toyota Safety Sense)
Tester Connection Condition Specified Condition
H43-3 (IG41) - B8-8 (IGB) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher
B8-8 (IGB) - Body ground and other terminals Always 10 kΩ or higher

Clearance Warning ECU Assembly (w/ Parking Support Brake System)
Tester Connection Condition Specified Condition
H43-3 (IG41) - O60-1 (IG) Always Below 1 Ω
H43-3 (IG41) - Body ground and other terminals Always 10 kΩ or higher
O60-1 (IG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK ENGINE STOP AND START ECU (OUTPUT VOLTAGE FOR EACH SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK ENGINE STOP AND START ECU (OUTPUT VOLTAGE FOR EACH SYSTEM)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Condition Specified Condition
O33-7 (+B) - Body ground*1 Always 10.5 to 16 V
O34-7 (+B) - Body ground*2 Always 10.5 to 16 V
H79-4 (+B1) - Body ground*3 Always 10.5 to 16 V
H82-10 (+B) - Body ground*4 Always 10.5 to 16 V
H61-2 (B) - Body ground*5 Always 10.5 to 16 V


*1: w/o Entry and Start System

*2: w/ Entry and Start System

*3: w/ Audio

*4: w/ Navigation System

*5: w/ Headup Display



c.

Turn the ignition switch ACC.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Condition Specified Condition
H79-15 (ACC1) - Body ground*1 Always 10.5 to 16 V


*1: w/ Audio



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Condition Specified Condition
O33-1 (IGR) - Body ground*1 Ignition switch ON 10.5 to 16 V
O34-1 (IGR) - Body ground*2 Ignition switch ON 10.5 to 16 V
H61-1 (IG) - Body ground*3 Ignition switch ON 10.5 to 16 V
H6-38 (IG+) - Body ground Ignition switch ON 10.5 to 16 V
H1-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V
H31-9 (IG+) - Body ground*4 Ignition switch ON 10.5 to 16 V
B8-8 (IGB) - Body ground*5 Ignition switch ON 10.5 to 16 V
O60-1 (IG) - Body ground*6 Ignition switch ON 10.5 to 16 V


*1: w/o Entry and Start System

*2: w/ Entry and Start System

*3: w/ Headup Display System

*4: for Automatic Air Conditioning System

*5: w/ Toyota Safety Sense

*6: w/ Parking Support Brake System



Result:
Proceed to
OK
NG



OK

CHECK POWER SOURCE CIRCUIT (POWER SOURCE CIRCUIT OF RELATED SYSTEM)

NG

6.CHECK AUDIO AND VISUAL SYSTEM
a.

Turn the ignition switch off and wait for 1 minute.


b.

Turn the ignition switch to ON.


c.

Lower the audio volume.


d.

Check if the audio and visual system operates normally.


OK:

Audio and visual system operates normally.


Result:
Proceed to
OK
NG



OK

END

NG

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H43 engine stop and start ECU connector.


b.

Disconnect the H79 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-12 (B42) - Body ground and other terminals Always 10 kΩ or higher
H79-4 (+B1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BIN TERMINAL POWER SOURCE CIRCUIT)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A3-11 (BIN) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ACC TERMINAL POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BATTERY)

9.CHECK HARNESS AND CONNECTOR (ACC TERMINAL POWER SOURCE CIRCUIT)
a.

Disconnect the A3 external backup boost converter (eco run vehicle converter assembly) connector.


b.

Turn the ignition switch to ACC.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A3-3 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



d.

Turn the ignition switch to off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A3-3 (ACC) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BODY GROUND)
a.

Disconnect the A3 external backup boost converter (eco run vehicle converter assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A3-6 (GND) - Body ground Ignition switch ACC Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the A3 external backup boost converter (eco run vehicle converter assembly) connector.


b.

Disconnect the H136 and H137 stereo component amplifier assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A3-5 (BO1) - H136-1 (+B) Always Below 1 Ω
A3-12 (ACO) - H137-12 (ACC) Always Below 1 Ω
A3-5 (BO1) - Body ground and other terminal Always Below 1 Ω
H136-1 (+B) - Body ground and other terminal Always 10 kΩ or higher
A3-12 (ACO) - Body ground and other terminal Always 10 kΩ or higher
H137-12 (ACC) - Body ground and other terminal Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the H136 and H137 stereo component amplifier assembly connectors


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H136-1 (+B) - Body ground Always 10.5 to 16 V



c.

Turn the Ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H137-12 (ACC) - Body ground Ignition switch ACC 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY)