Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2020.07–2020.09
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  STA Signal Circuit  


DESCRIPTION

While the engine is being cranked, a starter operation request signal is sent to terminal STA of the ECM.

HINT:

If there is an open in the STA circuit of the ECM, stop and start control will be prohibited after the third time the engine is started by stop and start control.

·

Stop and start control will be prohibited until the ignition switch is turned off.

·

The MIL will not illuminate.

·

If there is an open in the STA circuit of the ECM, the engine can still be started using the ignition switch, as the ECM also receives the starter operation request signal from the engine stop and start ECU via CAN communication. (Stop and start control is prohibited as the reliability of the signal sent via CAN communication cannot be assured while the voltage drops during operation of the starter assembly.)



A347476E32
2.667,0.51 4.604,0.75 1.938,0.24 10 false Starter operation request signal 4.26,1.615 5.823,1.833 1.563,0.219 10 false Starter operation request 4.26,2.094 5.823,2.313 1.563,0.219 10 false Starter operation request 5.719,2.479 7.115,3.052 1.396,0.573 10 false Engine Stop and Start ECU 2.385,2.115 3,2.313 0.615,0.198 10 false Open 0.583,2.51 1.042,2.708 0.458,0.198 10 false ECM 0.781,1.875 1.24,2.073 0.458,0.198 10 false STA 6.146,1.885 6.604,2.083 0.458,0.198 10 false STA 6.156,0.833 6.615,1.031 0.458,0.198 10 false CAN 0.75,0.823 1.208,1.021 0.458,0.198 10 false CAN 0.75,3.26 2.188,3.5 1.438,0.24 10 false from ST NO. 1 Fuse 0.75,4.74 2.083,5 1.333,0.26 10 false to Starter Assembly 3.885,4 5.115,4.198 1.229,0.198 10 false ST NO. 1 0.396,5.333 2.156,5.552 1.76,0.219 10 false : CAN Communication Line

WIRING DIAGRAM

for M15A-FKS


A428019E03
5.885,0.698 6.5,0.896 0.615,0.198 10 false CANH 0.917,0.698 1.531,0.896 0.615,0.198 10 false CANH 5.896,1.094 6.51,1.292 0.615,0.198 10 false CANL 0.938,1.094 1.552,1.292 0.615,0.198 10 false CANL 5.896,1.563 6.354,1.76 0.458,0.198 10 false STA 1,1.573 1.458,1.771 0.458,0.198 10 false STA 5.5,0.698 5.958,0.896 0.458,0.198 10 false H43 5.5,1.083 5.958,1.281 0.458,0.198 10 false H43 5.49,1.563 5.948,1.76 0.458,0.198 10 false A67 5.542,0.479 5.854,0.677 0.313,0.198 10 false 13 5.542,0.896 5.854,1.094 0.313,0.198 10 false 14 5.552,1.354 5.865,1.552 0.313,0.198 10 false 21 1.438,0.51 1.75,0.708 0.313,0.198 10 false 8 1.427,0.906 1.74,1.104 0.313,0.198 10 false 18 1.427,1.448 1.74,1.646 0.313,0.198 10 false 30 0.844,2.375 1.302,2.573 0.458,0.198 10 false A54 0.854,2.552 1.719,2.75 0.865,0.198 10 false ECM 5.344,2.385 7.135,2.74 1.792,0.354 10 false Engine Stop and Start ECU 0.875,4.677 2.26,4.99 1.385,0.313 10 false Auxiliary Battery 0.802,4.031 2.24,4.281 1.438,0.25 10 false BATT-MAIN NO. 1 1.667,3.698 2.896,3.896 1.229,0.198 10 false ST NO. 1 1.594,5.323 4.208,5.573 2.615,0.25 10 false : CAN Communication Line 3.188,4.302 4.417,4.5 1.229,0.198 10 false ST NO. 1 3.052,3.438 3.208,3.635 0.156,0.198 10 false 5 3.823,3.427 3.979,3.625 0.156,0.198 10 false 3 3.042,3.844 3.198,4.042 0.156,0.198 10 false 1 3.823,3.844 3.979,4.042 0.156,0.198 10 false 2 5.51,3.531 5.823,3.729 0.313,0.198 10 false D54 5.5,4 5.958,4.271 0.458,0.271 10 false D55 5.583,3.333 5.74,3.531 0.156,0.198 10 false 1 5.583,3.781 5.74,3.979 0.156,0.198 10 false 1 5.896,3.51 6.208,3.708 0.313,0.198 10 false ST 5.896,3.99 6.354,4.188 0.458,0.198 10 false ZYV 5.688,4.438 7.073,4.646 1.385,0.208 10 false Starter Assembly


for 1KR-FE


A472911E02
5.885,0.698 6.5,0.896 0.615,0.198 10 false CANH 0.917,0.698 1.531,0.896 0.615,0.198 10 false CANH 5.896,1.094 6.51,1.292 0.615,0.198 10 false CANL 0.938,1.094 1.552,1.292 0.615,0.198 10 false CANL 5.896,1.563 6.354,1.76 0.458,0.198 10 false STA 1,1.573 1.458,1.771 0.458,0.198 10 false STA 5.5,0.698 5.958,0.896 0.458,0.198 10 false H43 5.5,1.083 5.958,1.281 0.458,0.198 10 false H43 5.49,1.563 5.948,1.76 0.458,0.198 10 false A67 5.542,0.479 5.854,0.677 0.313,0.198 10 false 13 5.542,0.896 5.854,1.094 0.313,0.198 10 false 14 5.552,1.354 5.865,1.552 0.313,0.198 10 false 21 1.438,0.51 1.75,0.708 0.313,0.198 10 false 26 1.427,0.906 1.74,1.104 0.313,0.198 10 false 25 1.427,1.448 1.74,1.646 0.313,0.198 10 false 46 0.844,2.375 1.302,2.573 0.458,0.198 10 false A55 0.823,2.552 1.688,2.75 0.865,0.198 10 false ECM 5.344,2.385 7.135,2.74 1.792,0.354 10 false Engine Stop and Start ECU 0.875,4.677 2.26,4.99 1.385,0.313 10 false Auxiliary Battery 0.802,4.031 2.24,4.281 1.438,0.25 10 false BATT-MAIN NO. 1 1.667,3.698 2.896,3.896 1.229,0.198 10 false ST NO. 1 1.594,5.323 4.208,5.573 2.615,0.25 10 false : CAN Communication Line 3.188,4.302 4.417,4.5 1.229,0.198 10 false ST NO. 1 3.052,3.438 3.208,3.635 0.156,0.198 10 false 5 3.823,3.427 3.979,3.625 0.156,0.198 10 false 3 3.042,3.844 3.198,4.042 0.156,0.198 10 false 1 3.823,3.844 3.979,4.042 0.156,0.198 10 false 2 5.688,4.448 6.229,4.667 0.542,0.219 10 false D54 5.698,3.438 5.854,3.635 0.156,0.198 10 false 1 5.896,3.51 6.208,3.708 0.313,0.198 10 false ST 5.667,4.635 7.052,4.844 1.385,0.208 10 false Starter Assembly


PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

b.

Read the values displayed on the GTS when the ignition switch is ON and on (START).

OK:
GTS Display Condition Normal Condition
Starter SW Ignition switch ON OFF
Ignition switch START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK OPERATION
2.CHECK OPERATION
a.

Check the vehicle specification


Result:
Result Proceed to
for M15A-FKS A
for 1KR-FE B



A

3.CHECK HARNESS AND CONNECTOR (ECM - ST NO. 1 RELAY)

B

4.CHECK HARNESS AND CONNECTOR (ECM - ST NO. 1 RELAY)
3.CHECK HARNESS AND CONNECTOR (ECM - ST NO. 1 RELAY)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the A54 ECM connector.


c.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-30 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - ST NO. 1 RELAY)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the A55 ECM connector.


c.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-46 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR