The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear brake removal/installation are shown below.
Immediately after installing the brake shoes, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the brake shoes, the brake pedal may feel soft due to clearance between the rear brake shoe and brake drum. Depress the brake pedal several times until the brake pedal feels firm.
After replacing the brake shoes, always perform a road test to check the braking performance and check for vibrations.
When removing or installing the brake shoes or pushing back the wheel brake cylinder piston may cause a large clearance between the brake shoes and brake drum. When the brake pedal is depressed with a large clearance between the brake shoes and the brake drum, DTC C13DC00, C13DE00, C140000 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model)
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION (for HV Model)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISABLE BRAKE CONTROL (for HV Model)
3.REMOVE REAR WHEEL
4.DRAIN BRAKE FLUID
Immediately wash off any brake fluid that comes into contact with any painted surfaces.
5.REMOVE NO. 1 BOX SIDE PANEL
58912C
6.REMOVE NO. 2 BOX SIDE PANEL
58903A
7.REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY
58857A
8.REMOVE UPPER NO. 1 CONSOLE SUPPORT BRACKET
9.LOOSEN PARKING BRAKE CABLE
| *1 | No. 1 Wire Adjusting Nut |
Loosen the No. 1 wire adjusting nut
Do not reuse the loosened No. 1 wire adjusting nut.
42431D
10.REMOVE BRAKE DRUM
Release the parking brake and remove the brake drum.
If the brake drum cannot be removed easily, perform the following procedure.
| *1 | No. 1 Wire Adjusting Nut |
|
Contract |
Remove the hole plug and insert a screwdriver through the hole into the backing plate, and hold the automatic adjust lever away from the adjuster.
Using another screwdriver, contract the brake shoe by turning the adjusting bolt.
04495
11.REMOVE REAR BRAKE SHOE KIT
Using SST, separate the shoe return spring from the front brake shoe.
Do not damage the wheel cylinder boot.
Using needle-nose pliers, remove the shoe hold down spring cup, shoe hold down spring, shoe hold down spring pin and front brake shoe.
Remove the tension spring.
Remove the shoe return spring from the rear brake shoe and remove the parking brake shoe strut set.
Using needle-nose pliers, remove the shoe hold down spring cup, shoe hold down spring, shoe hold down spring pin and rear brake shoe.
Using needle-nose pliers, separate the No. 3 parking brake cable assembly.
47644A
12.REMOVE REAR BRAKE AUTOMATIC ADJUST LEVER
Remove the automatic adjust lever tension spring and remove the automatic adjust lever.
47550
13.REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY
Using a union nut wrench 10 mm, disconnect the brake tube from the rear wheel brake cylinder assembly.
Use a container to catch the brake fluid.
Remove the bolt and rear wheel brake cylinder assembly.