When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. The ECM uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the ECM determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| P057162 | Brake Switch "A" Signal Compare Failure | When the ignition switch is ON and the dynamic radar cruise control system is operating, the ECM detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more. | ·
Harness or connector ·
Stop light switch assembly ·
ECM |
Radar Cruise1 |
for M15A-FKS
for 1KR-FE
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the ECM, refer to Service Bulletin.
Disconnect the A63 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A63-2 (GND) - Body ground | Always | Below 1 Ω |
Connect the A63 stop light switch assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A63 stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A63-7 (B) - Body ground | Always | 11 to 14 V |
| A63-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| A63-6 (B) - Body ground | Ignition switch off | Below 1 V |
Connect the A63 stop light switch assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for M15A-FKS | A |
| for 1KR-FE | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Disconnect the A54 ECM connector.
Disconnect the A63 stop light switch assembly connector.
Disconnect the A36 skid control ECU (brake actuator assembly) connector.
Disconnect the H45 certification ECU (smart key ECU assembly) connector.
Disconnect the F19*1 or F20*2 shift lock control ECU (shift lock control unit assembly) connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Disconnect the D71 TCM connector.*
*: for CVT
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-22 (ST1-) - A63-5 (L) | Always | Below 1 Ω |
| A54-21 (STP) - A63-3 (L) | Always | Below 1 Ω |
| A54-22 (ST1-) or A63-5 (L) - Body ground | Always | 10 kΩ or higher |
| A54-21 (STP) or A63-3 (L) - Body ground | Always | 10 kΩ or higher |
Connect the D71 TCM connector.*
*: for CVT
Connect the F19*1 or F20*2 shift lock control ECU (shift lock control unit assembly) connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Connect the H45 certification ECU (smart key ECU assembly) connector.
Connect the A36 skid control ECU (brake actuator assembly) connector.
Connect the A63 stop light switch assembly connector.
Connect the A54 ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A54 ECM connector.
Disconnect the A63 stop light switch assembly connector.
Disconnect the A37 skid control ECU (brake actuator assembly) connector.
Disconnect the H45 certification ECU (smart key ECU assembly) connector.
Disconnect the F19*1 or F20*2 shift lock control ECU (shift lock control unit assembly) connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Disconnect the D71 TCM connector.*
*: for CVT
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-22 (ST1-) - A63-5 (L) | Always | Below 1 Ω |
| A54-21 (STP) - A63-3 (L) | Always | Below 1 Ω |
| A54-22 (ST1-) or A63-5 (L) - Body ground | Always | 10 kΩ or higher |
| A54-21 (STP) or A63-3 (L) - Body ground | Always | 10 kΩ or higher |
Connect the D71 TCM connector.*
*: for CVT
Connect the F19*1 or F20*2 shift lock control ECU (shift lock control unit assembly) connector.
*1: w/o Entry and Start System
*2: w/ Entry and Start System
Connect the H45 certification ECU (smart key ECU assembly) connector.
Connect the A37 skid control ECU (brake actuator assembly) connector.
Connect the A63 stop light switch assembly connector.
Connect the A54 ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A55 ECM connector.
Disconnect the A63 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A55-24 (ST1-) - A63-5 (L) | Always | Below 1 Ω |
| A55-57 (STP) - A63-3 (L) | Always | Below 1 Ω |
| A55-24 (ST1-) or A63-5 (L) - Body ground | Always | 10 kΩ or higher |
| A55-57 (STP) or A63-3 (L) - Body ground | Always | 10 kΩ or higher |
Connect the A63 stop light switch assembly connector.
Connect the A55 ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG