Home › Brake › BRAKE (REAR) › REAR BRAKE (for TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _089429 BRAKE (REAR) _0432132 REAR BRAKE(for TMMF Made) A

BRAKE (REAR)  REAR BRAKE(for TMMF Made)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47570 1.INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY

a.

Install the wheel brake cylinder with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.
C440292C01
1.76,2.948 2.073,3.146 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench 10 mm, install the brake tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 04495 2.INSTALL REAR BRAKE SHOE KIT

a.
C437957C01
0,0 0,0 false
V100155

High Temperature Grease


Apply high temperature grease to the surface of the backing plate which is in contact with the shoe.


b.
C108972

Using needle-nose pliers, connect the parking brake cable onto the parking brake shoe lever.


c.
C437955

Using pliers, install the rear brake shoe, shoe hold down pin and shoe hold down spring.


d.
C437958C01
0,0 0,0 false
V100155

High Temperature Grease


Apply high temperature grease to the adjusting bolt.


e.
C130279C02
0.672,0.296 1.930,0.518 1.259,0.222 10 *a 0.672,1.577 1.930,1.799 1.259,0.222 10 *b
*a Inside of Vehicle
*b Outside of Vehicle


Install the parking brake shoe strut set as shown in the illustration.


f.
C437954

Using pliers, install the front brake shoe, shoe hold down pin and shoe hold down spring.


g.
C437953N02
1.573,1.813 1.802,1.906 false 1.844,1.802 2.188,1.979 0.344,0.177 10 false SST

Using SST, install the tension spring.

SST
09703-30011  


h.
C437952N02
1.021,1.104 1.365,1.313 true 1.417,1.25 1.771,1.479 0.354,0.229 10 true SST

Using SST, install the return shoe spring.

SST
09703-30011  

NOTICE:

Do not damage the wheel cylinder boot.



Hide 3. CHECK REAR DRUM BRAKE INSTALLATION

a.

Check that each part is installed properly.

C241886C01
0.354,0.073 0.74,0.396 0.385,0.323 12 false *A 3.906,0.073 4.292,0.396 0.385,0.323 12 false *B
*A for LH Side *B for RH Side
V100135

Front of the Vehicle - -



b.
C130281

Measure the rear brake drum sub-assembly inner diameter and the diameter of the brake shoes. Check that the difference between the diameters is equal to the specified shoe clearance.

Shoe clearance:

0.6 mm (0.024 in.)


NOTICE:

There should be no oil or grease adhering to the friction surfaces of the shoe lining or the rear brake drum sub-assembly.



Hide 42431D 4.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

a.

Install the rear brake drum sub-assembly.


Hide 6.BLEED CLUTCH LINE (for Manual Transmission)

Hide 7.ADJUST REAR DRUM BRAKE SHOE CLEARANCE

NOTICE:

Do not use screwdrivers or any other tools to rotate the adjuster.


a.

Press the brake pedal 30 times (not the parking brake). The clearance between the brake shoes and drum will be adjusted automatically.


Hide 8.INSTALL REAR WHEEL