Home › General › MAINTENANCE › REAR DRUM BRAKE SHOE (for TMC Made) › from 2020.07
RM36W0E _V1 General _088300 MAINTENANCE _0432136 REAR DRUM BRAKE SHOE(for TMC Made) A

MAINTENANCE  REAR DRUM BRAKE SHOE(for TMC Made)  INSTALLATION  


PROCEDURE

Hide 47644A 1.INSTALL REAR BRAKE AUTOMATIC ADJUST LEVER

a.

Install the automatic adjust lever and automatic adjust lever tension spring to the front brake shoe.


Hide 04495 2.INSTALL REAR BRAKE SHOE KIT

a.
C430615C01
0,0 0,0 false
V100144

High Temperature Grease


Apply high temperature grease to the surface of the backing plate which is in contact with the shoe.


b.
C108972

Using a needle nose plier, install the No. 3 parking brake cable assembly to the parking brake shoe lever.


c.
C430603

Using a needle nose plier, install the rear brake shoe, shoe hold down spring pin, shoe hold down spring and shoe hold down spring cup.


d.
C235450C08
0,0 0,0 false
V100144

High Temperature Grease


Apply high temperature grease to the adjusting bolt.


e.
C434846

Install the parking brake shoe strut set as shown in the illustration.


f.
C430602

Using a needle nose plier, install the front brake shoe, shoe hold down spring pin, shoe hold down spring and shoe hold down spring cup.


g.
C434845

Using a needle-nose plier, install the tension spring to the front brake shoe and rear brake shoe.


h.
C434843N01
1.083,1.344 1.469,1.385 true 0.74,1.281 1.094,1.479 0.354,0.198 10 true SST

Using SST, install the shoe return spring to the front brake shoe.

SST
09921-00011  

NOTICE:

Do not damage the wheel cylinder boot.



Hide 42431D 3. BRAKE DRUM

a.

Inspect that each part is installed properly as shown in the illustration.

C241885C04
0.24,0.094 0.552,0.292 0.313,0.198 10 false *A 3.948,0.094 4.26,0.292 0.313,0.198 10 false *B
*A for LH Side *B for RH Side
V100135

Front of the Vehicle - -


NOTICE:

There should be no oil or grease adhering to the friction surfaces of the shoe lining or the drum.



Hide 42431D 4.INSTALL BRAKE DRUM

a.

Install the rear brake drum.


Hide 5.ADJUST REAR DRUM BRAKE SHOE CLEARANCE

a.

Provisionally install the hub nuts.


b.

Remove the shoe adjusting hole plug.


c.
C434842C01
1.74,1.323 2.302,0.99 true 2.375,0.854 2.646,1.063 0.271,0.208 10 true *1
*1 Automatic Adjust Lever
V113147

Expand


Using a screwdriver, turn the adjuster to expand the shoe until the drum locks.


d.
C434841C01
1.74,1.354 2.25,1.021 true 2.333,0.885 2.583,1.104 0.25,0.219 10 true *1
*1 Automatic Adjust Lever
V113147

Contract


Hold the automatic adjust lever away from the adjuster, and contract the brake shoe by turning the adjust bolt using another screwdriver until the drum can rotate smoothly.


e.

Install the shoe adjusting hole plug.


Hide 6.INSTALL REAR WHEEL

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

Hide 9. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HV Model)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART