Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2020.07–2020.09
RM36W0E _59 Vehicle Exterior _087824 LIGHTING (EXT) _0419675 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the clearance light*1, taillight and license plate light.

*1: for Halogen Headlight


WIRING DIAGRAM

E438262E03
4.115,3.958 6.292,4.615 2.177,0.656 10 false Power Distribution Box Assembly 0.625,4.813 2.208,5.042 1.583,0.229 10 false *1: for Halogen Headlight 1.042,2.583 2.521,2.823 1.479,0.24 10 false Headlight Assembly LH 4.833,1.688 5.146,1.885 0.313,0.198 10 false +B 5.385,0.865 5.698,1.063 0.313,0.198 10 false IC 4.854,3.292 6.198,3.583 1.344,0.292 10 false CXPI Transceiver 3.573,1.969 3.885,2.167 0.313,0.198 10 false 4E 3.594,1.75 3.906,1.948 0.313,0.198 10 false 30 4.25,1.979 4.563,2.177 0.313,0.198 10 false IPD 5.5,4.844 7.135,5.438 1.635,0.594 10 false Main Body ECU (Multiplex Network Body ECU) 0.958,5.292 2.698,5.49 1.74,0.198 10 false : CXPI Communication Line 1.042,2.427 2.5,3.031 1.458,0.604 10 false A10 2.25,1.99 2.802,2.354 0.552,0.365 10 false B 1.219,1.99 1.729,2.333 0.51,0.344 10 false E 1.042,1.875 1.594,2.24 0.552,0.365 10 false 2 2.438,1.885 2.99,2.25 0.552,0.365 10 false 1 1.01,3.906 2.573,4.135 1.563,0.229 10 false Headlight Assembly RH 1.021,3.74 2.479,4.344 1.458,0.604 10 false A11 1.208,3.26 1.719,3.604 0.51,0.344 10 false E 2.24,3.271 2.792,3.635 0.552,0.365 10 false B 1.052,3.167 1.604,3.531 0.552,0.365 10 false 2 2.427,3.177 2.979,3.542 0.552,0.365 10 false 1 2.854,4.917 3.406,5.281 0.552,0.365 10 false A 2.646,1.896 3.198,2.26 0.552,0.365 10 false *1 2.656,3.135 3.208,3.5 0.552,0.365 10 false *1 0.125,0.156 1.604,0.396 1.479,0.24 12 false for HV Model:

E440212E02
3.99,3.958 6.198,4.458 2.208,0.5 10 false Power Distribution Box Assembly 0.521,4.865 2.667,5.156 2.146,0.292 10 false *1: for Halogen Headlight 1.031,2.583 2.49,3.188 1.458,0.604 10 false Headlight Assembly LH 5.365,0.792 5.677,0.99 0.313,0.198 10 false IC 4.865,3.302 6.208,3.594 1.344,0.292 10 false CXPI Transceiver 3.594,1.958 3.906,2.156 0.313,0.198 10 false 4D 3.594,1.771 3.906,1.969 0.313,0.198 10 false 18 3.583,2.823 3.896,3.021 0.313,0.198 10 false 4E 3.594,2.604 3.906,2.802 0.313,0.198 10 false 30 5.448,4.844 7.094,5.375 1.646,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,5.292 2.677,5.5 1.708,0.208 10 false : CXPI Communication Line 5.135,2.531 5.448,2.729 0.313,0.198 10 false +B 1.031,2.417 2.49,3.021 1.458,0.604 10 false A10 2.24,1.99 2.792,2.354 0.552,0.365 10 false B 1.219,1.99 1.729,2.333 0.51,0.344 10 false E 1.042,1.875 1.594,2.24 0.552,0.365 10 false 2 2.438,1.885 2.99,2.25 0.552,0.365 10 false 1 1.031,3.875 2.51,4.104 1.479,0.229 10 false Headlight Assembly RH 1.052,3.719 2.51,4.323 1.458,0.604 10 false A11 1.208,3.26 1.719,3.604 0.51,0.344 10 false E 2.24,3.271 2.792,3.635 0.552,0.365 10 false B 1.052,3.167 1.604,3.531 0.552,0.365 10 false 2 2.427,3.177 2.979,3.542 0.552,0.365 10 false 1 3.021,4.906 3.573,5.271 0.552,0.365 10 false A 2.99,1.875 3.542,2.24 0.552,0.365 10 false *1 4.552,2.792 4.865,2.99 0.313,0.198 10 false IPD 0.177,0.219 2.104,0.646 1.927,0.427 12 false for Gasoline Model:

E438261E05
5.469,6.135 7.115,6.844 1.646,0.708 10 false Main Body ECU (Multiplex Network Body ECU) 5.167,0.219 5.323,0.417 0.156,0.198 10 false A 2.042,2.063 5.031,2.313 2.99,0.25 10 false Rear Combination Light Lens and Body LH 2.021,3.76 4.99,4.052 2.969,0.292 10 false Rear Combination Light Lens and Body RH 1.677,5.542 3.74,5.813 2.063,0.271 10 false License Plate Light Assembly LH 1.698,7.083 3.802,7.292 2.104,0.208 10 false License Plate Light Assembly RH 2.042,1.896 2.615,2.271 0.573,0.375 10 false O107 2.021,3.594 2.594,3.969 0.573,0.375 10 false O108 1.667,5.375 2.24,5.75 0.573,0.375 10 false Y3 1.688,6.906 2.26,7.281 0.573,0.375 10 false Y4 2.156,1.49 2.729,1.865 0.573,0.375 10 false E 4.104,1.479 4.677,1.854 0.573,0.375 10 false B 4.302,1.344 4.875,1.719 0.573,0.375 10 false 2 1.969,1.365 2.542,1.74 0.573,0.375 10 false 1 2.146,3.156 2.719,3.531 0.573,0.375 10 false E 1.969,3.042 2.542,3.417 0.573,0.375 10 false 1 4.115,3.167 4.688,3.542 0.573,0.375 10 false B 4.323,3.031 4.896,3.406 0.573,0.375 10 false 2 3.438,4.896 4.01,5.271 0.573,0.375 10 false B 1.875,4.896 2.448,5.271 0.573,0.375 10 false E 1.688,4.771 2.26,5.146 0.573,0.375 10 false 2 3.635,4.781 4.208,5.156 0.573,0.375 10 false 1 3.49,6.448 4.063,6.823 0.573,0.375 10 false B 3.656,6.354 4.229,6.729 0.573,0.375 10 false 1 1.875,6.458 2.448,6.833 0.573,0.375 10 false E 1.708,6.365 2.281,6.74 0.573,0.375 10 false 2 0.24,0.177 2.667,0.5 2.427,0.323 12 false for LED Headlight:

E438261E06
5.479,6.135 7.115,6.563 1.635,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 5.167,0.219 5.323,0.417 0.156,0.198 10 false A 2.021,2.083 5.01,2.573 2.99,0.49 10 false Rear Combination Light Lens and Body LH 2.01,3.76 5.094,4.115 3.083,0.354 10 false Rear Combination Light Lens and Body RH 1.688,5.542 3.75,5.813 2.063,0.271 10 false License Plate Light Assembly LH 1.708,7.094 3.771,7.365 2.063,0.271 10 false License Plate Light Assembly RH 2.042,1.906 2.615,2.281 0.573,0.375 10 false O103 2,3.594 2.573,3.969 0.573,0.375 10 false O104 1.677,5.385 2.25,5.76 0.573,0.375 10 false Y3 1.708,6.927 2.281,7.302 0.573,0.375 10 false Y4 2.156,1.49 2.729,1.865 0.573,0.375 10 false E 4.104,1.479 4.677,1.854 0.573,0.375 10 false B 4.302,1.344 4.875,1.719 0.573,0.375 10 false 2 1.969,1.365 2.542,1.74 0.573,0.375 10 false 1 2.156,3.146 2.729,3.521 0.573,0.375 10 false E 1.969,3.042 2.542,3.417 0.573,0.375 10 false 1 4.115,3.167 4.688,3.542 0.573,0.375 10 false B 4.323,3.031 4.896,3.406 0.573,0.375 10 false 2 3.448,4.885 4.021,5.26 0.573,0.375 10 false B 1.885,4.885 2.458,5.26 0.573,0.375 10 false E 1.677,4.792 2.25,5.167 0.573,0.375 10 false 2 3.625,4.792 4.198,5.167 0.573,0.375 10 false 1 3.469,6.458 4.042,6.833 0.573,0.375 10 false B 3.656,6.333 4.229,6.708 0.573,0.375 10 false 1 1.875,6.458 2.448,6.833 0.573,0.375 10 false E 1.698,6.365 2.271,6.74 0.573,0.375 10 false 2 0.156,0.281 2.5,0.875 2.344,0.594 12 false for Halogen Headlight:

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Input Signal Tail light input OFF or ON OFF: Taillight is not input
ON: Tail light is input
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Input Signal
50003 475 1290
OK:

Display changes according to the taillight illumination condition.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Turn the light control switch to the TAIL position.


b.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Result Proceed to
OK A
NG (for LED Headlight) B
NG (for Halogen Headlight) C



A

3.READ VALUE USING GTS

B

4.INSPECT REAR COMBINATION LIGHT LENS AND BODY LH

C

9.INSPECT REAR COMBINATION LIGHT LENS AND BODY LH
3.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Output Signal Tail light output OFF or ON OFF: Taillight is not output
ON: Tail light is output
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Output Signal
50003 475 1291
OK:

Display changes according to the taillight illumination condition.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.INSPECT REAR COMBINATION LIGHT LENS AND BODY LH
a.

Disconnect the O107 rear combination light lens and body LH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT REAR COMBINATION LIGHT LENS AND BODY RH
5.INSPECT REAR COMBINATION LIGHT LENS AND BODY RH
a.

Disconnect the O108 rear combination light lens and body RH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT LICENSE PLATE LIGHT ASSEMBLY LH
6.INSPECT LICENSE PLATE LIGHT ASSEMBLY LH
a.

Disconnect the Y3 license plate light assembly LH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

REPLACE LICENSE PLATE LIGHT ASSEMBLY LH

NG

7.INSPECT LICENSE PLATE LIGHT ASSEMBLY RH
7.INSPECT LICENSE PLATE LIGHT ASSEMBLY RH
a.

Disconnect the Y4 license plate light assembly RH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

REPLACE LICENSE PLATE LIGHT ASSEMBLY RH

NG

8.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR COMBINATION LIGHT LENS AND BODY AND LICENSE PLATE LIGHT ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR COMBINATION LIGHT LENS AND BODY AND LICENSE PLATE LIGHT ASSEMBLY)
a.

Disconnect the O107 rear combination light lens and body LH connector.


b.

Disconnect the O108 rear combination light lens and body RH connector.


c.

Disconnect the Y3 license plate light assembly LH connector.


d.

Disconnect the Y4 license plate light assembly RH connector.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.


f.

Disconnect the 4E power distribution box assembly connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O107-2 (B) or 4E-30 - Body ground Always 10 kΩ or higher
O108-2 (B) or 4E-30 - Body ground Always 10 kΩ or higher
Y3-1 (B) or 4E-30 - Body ground Always 10 kΩ or higher
Y4-1 (B) or 4E-30 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT REAR COMBINATION LIGHT LENS AND BODY LH
a.

Disconnect the O103 rear combination light lens and body LH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

10.INSPECT REAR COMBINATION LIGHT LENS AND BODY RH
10.INSPECT REAR COMBINATION LIGHT LENS AND BODY RH
a.

Disconnect the O104 rear combination light lens and body RH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

11.INSPECT LICENSE PLATE LIGHT ASSEMBLY LH
11.INSPECT LICENSE PLATE LIGHT ASSEMBLY LH
a.

Disconnect the Y3 license plate light assembly LH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

REPLACE LICENSE PLATE LIGHT ASSEMBLY LH

NG

12.INSPECT LICENSE PLATE LIGHT ASSEMBLY RH
12.INSPECT LICENSE PLATE LIGHT ASSEMBLY RH
a.

Disconnect the Y4 license plate light assembly RH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights or clearance lights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

REPLACE LICENSE PLATE LIGHT ASSEMBLY RH

NG

13.INSPECT HEADLIGHT ASSEMBLY RH
13.INSPECT HEADLIGHT ASSEMBLY RH
a.

Disconnect the A11 headlight assembly RH connector.


b.

Turn the light control switch to the AUTO (OFF) position.

NOTICE:

If the low beam headlights illuminate when the ignition switch is turned ON, shine a light on the automatic light control sensor to turn the low beam headlights off before operating the headlight dimmer switch.



c.

Turn the light control switch to the TAIL position.


d.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tail Light Fuse Shut Off Status Tail light fuse condition OFF or ON OFF: Taillight fuse not shut off
ON: Taillight fuse shut off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Tail Light Fuse Shut Off Status
50003 475 1293
OK:

The Data List value displays "OFF".



Result:
Result Proceed to
OK A
NG (for HV Headlight) B
NG (for Gasoline Headlight) C



A

B

14.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR COMBINATION LIGHT LENS AND BODY AND LICENSE PLATE LIGHT ASSEMBLY)

C

15.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR COMBINATION LIGHT LENS AND BODY AND LICENSE PLATE LIGHT ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR COMBINATION LIGHT LENS AND BODY AND LICENSE PLATE LIGHT ASSEMBLY)
a.

Disconnect the O107 rear combination light lens and body LH connector.


b.

Disconnect the O108 rear combination light lens and body RH connector.


c.

Disconnect the Y3 license plate light assembly LH connector.


d.

Disconnect the Y4 license plate light assembly RH connector.


e.

Disconnect the A10 headlight assembly LH connector.


f.

Disconnect the A11 headlight assembly RH connector.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Disconnect the 4D power distribution box assembly connector.


i.

Disconnect the 4E power distribution box assembly connector.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A10-1 (B) or 4D-18 - Body ground Always 10 kΩ or higher
A11-1 (B) or 4D-18 - Body ground Always 10 kΩ or higher
O107-2 (B) or 4E-30 - Body ground Always 10 kΩ or higher
O108-2 (B) or 4E-30 - Body ground Always 10 kΩ or higher
Y3-1 (B) or 4E-30 - Body ground Always 10 kΩ or higher
Y4-1 (B) or 4E-30 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR COMBINATION LIGHT LENS AND BODY AND LICENSE PLATE LIGHT ASSEMBLY)
a.

Disconnect the O107 rear combination light lens and body LH connector.


b.

Disconnect the O108 rear combination light lens and body RH connector.


c.

Disconnect the Y3 license plate light assembly LH connector.


d.

Disconnect the Y4 license plate light assembly RH connector.


e.

Disconnect the A10 headlight assembly LH connector.


f.

Disconnect the A11 headlight assembly RH connector.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Disconnect the 4E power distribution box assembly connector.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A10-1 (B) or 4E-30 - Body ground Always 10 kΩ or higher
A11-1 (B) or 4E-30 - Body ground Always 10 kΩ or higher
O107-2 (B) or 4E-30 - Body ground Always 10 kΩ or higher
O108-2 (B) or 4E-30 - Body ground Always 10 kΩ or higher
Y3-1 (B) or 4E-30 - Body ground Always 10 kΩ or higher
Y4-1 (B) or 4E-30 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR