Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › WATER PUMP WITH MOTOR › from 2020.07
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0424588 WATER PUMP WITH MOTOR A

HYBRID / BATTERY CONTROL  WATER PUMP WITH MOTOR  INSTALLATION  


PROCEDURE

Hide G9040 1.INSTALL INVERTER WATER PUMP ASSEMBLY

a.

Connect the outlet No. 1 hybrid water pump hose and inlet hybrid water pump hose to the inverter water pump assembly and slide the 2 clips to secure them.

A466675C01
1.531,1.292 1.708,1.125 true 1.51,0.667 1.729,1.01 true 6.531,0.531 6.75,0.875 true 6.844,0.875 6.969,1.24 true 0.167,0.438 0.479,0.635 0.313,0.198 10 false *2 0.635,0.417 0.948,0.615 0.313,0.198 10 false *e 1.021,0.729 1.333,0.927 0.313,0.198 10 false *f 1.219,0.927 1.531,1.125 0.313,0.198 10 false *d 1.354,1.271 1.667,1.469 0.313,0.198 10 false *c 0.729,1.188 1.104,1.385 0.375,0.198 10 false 135° 1.365,0.521 1.677,0.719 0.313,0.198 10 false *b 5.146,0.427 5.458,0.625 0.313,0.198 10 false *1 5.75,1.156 6.125,1.354 0.375,0.198 10 false 120° 5.427,1.26 5.74,1.458 0.313,0.198 10 false *g 6.125,0.771 6.438,0.969 0.313,0.198 10 false *f 6.385,0.406 6.698,0.604 0.313,0.198 10 false *a 6.896,1.26 7.125,1.448 0.229,0.188 10 false *c 6.646,1.271 6.875,1.458 0.229,0.188 10 false *d
*1 Outlet No. 1 Hybrid Water Pump Hose *2 Inlet Hybrid Water Pump Hose
*a Alignment Mark (White or Red) *b Alignment Mark (Pink or White)
*c Rib *d 2 to 5 mm (0.0787 to 0.197 in.)
*e Front of Vehicle *f RH Side
*g Down - -


NOTICE:

To prevent foreign matter from entering the inverter water pump assembly and inverter cooling system, do not remove the pieces of cloth from the pipes and disconnected hoses until installation.


HINT:
·

Make sure to align the alignment marks of the hoses with the ribs of the inverter water pump assembly.

·

Make sure that the clips are positioned as shown in the illustration.




b.

Temporarily install the inverter water pump assembly to the fan shroud assembly with the 2 bolts.


c.

Fully tighten the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

As overtightening the bolts may damage the fan shroud assembly, make sure to use a torque wrench.



d.

Connect the inverter water pump assembly connector.

NOTICE:

If a dustproof cap is installed to the inverter water pump assembly connector, do not remove it until the connector is to be connected.



Hide 51451A 4.INSTALL CENTER ENGINE UNDER COVER (w/ Cover)