48811
1.INSTALL FRONT STABILIZER BAR
2.INSTALL STEERING LINK ASSEMBLY
48069
3.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
| *A | for TMC Made |
| *B | for TMMF Made |
Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.
48068
4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
12363A
5.INSTALL ENGINE MOVING CONTROL ROD
Install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.
51228G
6.INSTALL FRONT SUSPENSION MEMBER PLATE (w/ Plate)
Install the front suspension member plate to the front suspension member sub-assembly with the 2 bolts.
51201
7.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Slowly jack up the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.
The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.
If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments to keep the front suspension crossmember sub-assembly level.
Make sure that the front suspension crossmember sub-assembly not hit the protrusion of the reinforcement.
| *a | OK |
| *b | NG |
After installation, check that the claws of the steering column hole cover base are not disengaged.
Install the front suspension crossmember sub-assembly to the vehicle body with the 8 bolts (A).
Install the 2 bolts (B).
Lower the engine lifter.
Install the engine moving control rod with the bolt.
except 1KR-FE:
Install the wiring harness clamp bracket to the front suspension crossmember sub-assembly with the bolt.
17410
8.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1KR-FE)
57543C
9.INSTALL FRONT FLOOR CENTER BRACE (for 1KR-FE)
48069
10.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMC Made)
48069
11.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMMF Made)
48068
12.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMC Made)
Perform the same procedure as for the LH side.
48068
13.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMMF Made)
Perform the same procedure as for the LH side.
45047
14.CONNECT TIE ROD END SUB-ASSEMBLY LH (for TMC Made)
Connect the tie rod end sub-assembly LH to the steering knuckle LH with the nut.
Do not damage the ball joint dust cover.
Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.
Install a new cotter pin.
45047
15.CONNECT TIE ROD END SUB-ASSEMBLY LH (for TMMF Made)
Connect the tie rod end sub-assembly LH to the steering knuckle LH with the nut.
Do not damage the ball joint dust cover.
Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.
Install a new cotter pin.
|
Install in this Direction |
Engage the claw to install the new steering knuckle seal as shown in the illustration.
Check that the steering knuckle seal is securely installed.
45046
16.CONNECT TIE ROD END SUB-ASSEMBLY RH (for TMC Made)
Perform the same procedure as for the LH side.
45046
17.CONNECT TIE ROD END SUB-ASSEMBLY RH (for TMMF Made)
Perform the same procedure as for the LH side.
48810
18.CONNECT FRONT STABILIZER LINK ASSEMBLY LH
Connect the front stabilizer link assembly LH to the front stabilizer bar with the nut.
Do not damage the boot of the ball joint.
If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.
48820B
19.CONNECT FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
53876A
20.INSTALL FRONT FENDER LINER LH (w/ Engine Under Cover Assembly)
Install the front fender liner LH to the vehicle body with the 2 screws.
53875A
21.INSTALL FRONT FENDER LINER RH (w/ Engine Under Cover Assembly)
Perform the same procedure as for the LH side.
22.INSTALL FRONT WHEELS
45260
23.CONNECT NO.2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
24.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)
45259A
25.INSTALL COLUMN HOLE COVER SILENCER SHEET (for RHD)
26. STABILIZE SUSPENSION
48069
27.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMC Made)
48069
28.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for TMMF Made)
48068
29.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMC Made)
48068
30.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for TMMF Made)
51447D
31.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)
Install the center No. 4 engine under cover to the vehicle with the 2 bolts and 2 nuts.
51447D
32.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMMF Made)
except 1KR-FE:
Install the center No. 4 engine under cover to the vehicle with the 4 bolts.
51442C
33.INSTALL ENGINE UNDER COVER LH
w/ Center Engine Under Cover for Full Cover Type, w/ Center Engine Under Cover for Half Cover Type:
Install the engine under cover LH to the vehicle with the 2 clips.
w/o Center Engine Under Cover:
Install the engine under cover LH to the vehicle with the 3 clips.
51441C
34.INSTALL ENGINE UNDER COVER RH
Perform the same procedure as for the LH side.
51451A
35.INSTALL CENTER ENGINE UNDER COVER
w/ Center Engine Under Cover for Full Cover Type:
Install the center engine under cover to the vehicle with the 4 bolts, 4 screws and 9 clips.
w/ Center Engine Under Cover for Half Cover Type:
Install the center engine under cover to the vehicle with the 4 bolts, 4 screws and 7 clips.
36.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT