Home › Engine / Hybrid System › 1KR-FE (STARTING) › STARTER (w/ Stop And Start System) › from 2020.07
RM36W0E _51 Engine / Hybrid System _091207 1KR-FE STARTING _0432155 STARTER(w/ Stop And Start System) A

1KR-FE STARTING  STARTER(w/ Stop And Start System)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during starter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51451A 3.REMOVE CENTER ENGINE UNDER COVER

Hide 4.REMOVE AIR CAP WITH AIR CLEANER HOSE

a.
A470098

Disconnect the connector.


b.

Disconnect the clamp.


c.

Loosen the hose clamp and remove the air cleaner hose from the throttle body assembly.


d.

Disconnect the 2 clamp hooks from the air cleaner cap sub-assembly.


e.

Disengage the 2 guides and separate the air cleaner cap sub-assembly together with air cleaner hose assembly from the air cleaner case sub-assembly.


Hide 17801 5.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 7.REMOVE AUXILIARY BATTERY

Hide 74404A 9.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 33820B 10.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C116858

Remove the 2 clips (A) to disconnect the transmission control cable assembly from the manual transaxle assembly.


b.

Remove the 2 clips (B) to disconnect the transmission control cable assembly from the control cable bracket assembly.


Hide 11363A 11.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
A323988

Disengage the claw by pulling the flywheel housing side cover outward and remove the flywheel housing side cover.


Hide 28100 12.REMOVE STARTER ASSEMBLY

a.
A470064

Open the terminal cap.


b.

Remove the nut and disconnect terminal 30.


c.

Disconnect the starter assembly connector.


d.

Disengage the wire harness clamp.


e.
A470065

Remove the 2 bolts and starter assembly.


f.
A470066

Remove the bolt and wire harness clamp bracket from the starter assembly.