Home › Drivetrain › C551 (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE UNIT › from 2020.07
RM36W0E _52 Drivetrain _091208 C551 MANUAL TRANSMISSION / TRANSAXLE _0432175 MANUAL TRANSAXLE UNIT A

C551 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE NO. 1 CLUTCH HOUSING COVER

Hide 31230 2.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31204 3.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31207A 4.REMOVE CLUTCH RELEASE FORK SHAFT OIL SEAL

Hide 33104 5.REMOVE MANUAL TRANSAXLE DRAIN PLUG

a.

Remove the manual transaxle drain plug and gasket from the manual transmission case.


Hide 33101A 6.REMOVE MANUAL TRANSAXLE FILLER PLUG

a.

Remove the manual transaxle filler plug and gasket from the manual transmission case.


Hide 84210 7.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
C245794

Disengage the 2 clamps to disconnect the wire harness connector.


b.
C230530E01
2.992,0.958 3.325,1.132 0.334,0.174 10 SST 2.234,0.676 2.88,1.04 2.88,1.04 2.978,1.04 false

Using SST, remove the back-up light switch assembly and gasket from the manual transmission case.

SST
09817-16011  


Hide 8.REMOVE CONTROL CABLE BRACKET

a.
C121109

Remove the 2 bolts and control cable bracket.


Hide 9.REMOVE NEUTRAL POSITION SWITCH (w/ Stop And Start System)

a.
C304779E01
1.656,1.603 2.004,1.783 0.348,0.179 10 SST 1.849,1.329 1.831,1.581 false

Using SST, remove the neutral position switch and gasket from the manual transmission case.

SST
09817-16011  


Hide 33295B 10.REMOVE SHIFT GATE PIN

a.
F100316

Remove the shift gate pin from the manual transmission case.


Hide 11.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.

w/ Stop And Start System:

i.
C310756

Remove the 4 bolts, washer and the shift and select lever shaft assembly from the manual transmission case.



b.

w/o Stop And Start System:

i.

Remove the 4 bolts and the shift and select lever shaft assembly from the manual transmission case.



c.

Remove the select return compression spring from the manual transmission case.


Hide 33451H 12.REMOVE REVERSE IDLER GEAR SHAFT BOLT

a.
C244245

Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.


Hide 33111 13.REMOVE MANUAL TRANSMISSION CASE

a.
F100320

Remove the 5 bolts from the manual transaxle case side.


b.
F100319

Remove the 8 bolts from the manual transmission case side.


c.

Using a plastic hammer, remove the manual transmission case from the manual transaxle case.


Hide 33451 14.REMOVE REVERSE IDLER GEAR SHAFT

a.
G020851

Remove the reverse idler gear shaft from the manual transaxle case.


Hide 33402 15.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

a.

Remove the reverse idler gear sub-assembly from the manual transaxle case.


Hide 33240 16.REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY

a.
G020852

Remove the 2 bolts and reverse shift arm bracket assembly from the manual transaxle case.


Hide 33242 17.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
G020853

Remove the bolt from No. 1 gear shift fork shaft.


b.
G020854

Using a pin punch and a hammer, remove the slotted spring pin from the No. 1 gear shift head.


c.
G020855

Remove No. 1 gear shift fork shaft, No. 1 gear shift head and the No. 1 gear shift fork from manual transaxle case.


d.
G020856

Hold the No. 1 gear shift fork shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Using 2 screwdrivers and a hammer, remove the snap ring from the No. 1 gear shift fork shaft.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33244G 18.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
G020857

Remove the straight pin from the No. 3 gear shift fork.


b.
G020858

Using a pin punch and a hammer, remove the slotted spring pin from the No. 3 gear shift head.


c.
G020859

Using 2 screwdrivers and a hammer, remove the snap ring from the No. 3 gear shift fork shaft.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



d.
G020860

Remove the No. 3 gear shift fork shaft, compression spring, No. 3 gear shift head and No. 3 gear shift fork from the manual transaxle case.


e.
G020861

Hold the No. 3 gear shift fork shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



f.

Using 2 screwdrivers and a hammer, remove the snap ring from the No. 3 gear shift fork shaft.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33243A 19.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

a.
D005727

Using a magnet hand, remove the straight pin from the reverse shift fork.


b.
C231089

While lifting the reverse shift fork, using 2 screwdrivers and a hammer, remove the snap ring from the No. 2 gear shift fork shaft.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



c.
G020913

Remove the bolt from the No. 2 gear shift fork.


d.
G020914

Shift the No. 2 gear shift fork and No. 2 transmission hub sleeve to the 4th gear position.


e.

Remove the No. 2 gear shift fork shaft, No. 2 gear shift fork and reverse shift fork.


f.
G020915

Hold the No. 2 gear shift fork shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



g.

Using 2 screwdrivers and a hammer, remove the snap ring from the No. 2 gear shift fork shaft.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 20.REMOVE INPUT SHAFT ASSEMBLY

a.
G020916

Remove the input shaft assembly from the manual transaxle case.


Hide 21.REMOVE OUTPUT SHAFT ASSEMBLY

a.

Remove the output shaft assembly from the manual transaxle case.


Hide 22.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
G021163

Remove the differential case assembly from the manual transaxle case.


Hide 23.REMOVE NO. 2 OIL RECEIVER PIPE

a.
C230550

Remove the No. 2 oil receiver pipe from the manual transmission case.

NOTICE:

Do not damage No. 2 oil receiver pipe.



Hide 33449 24.REMOVE TRANSMISSION MAGNET

a.
G021178

Remove the transmission magnet from the manual transaxle case.


Hide 31105D 25.REMOVE FRONT TRANSAXLE CASE OIL SEAL

a.
G020921C04
2.677,0.125 1.781,0.948 false 2.708,0 2.948,0.208 0.24,0.208 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, pry out the manual transaxle case oil seal.

NOTICE:

Do not damage the installation surfaces of the manual transaxle case.



Hide 33321N 26.REMOVE OUTPUT SHAFT FRONT BEARING

a.
G020922E04
1.281,1.146 0.906,0.969 false 0.542,0.833 0.99,1.031 0.448,0.198 10 false SST

Using SST, remove the output shaft front bearing (outer race) from the manual transaxle case.

SST
09308-00010  


Hide 33134B 27.REMOVE OUTPUT SHAFT COVER

a.
G020987

Remove the output shaft cover from the manual transaxle case.


Hide 28.REMOVE TRANSMISSION CASE OIL SEAL

a.
C230551E02
0.153,0.219 0.461,0.407 0.308,0.188 10 SST 0.899,0.478 0.504,0.307 false

Using SST, remove the transmission case oil seal from the manual transmission case.

SST
09308-00010  

NOTICE:

Do not damage the installation surfaces of the manual transmission case.



Hide 41311F 29.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
G020989E05
1.542,1.458 2.365,1.833 2.365,1.833 1.417,1.156 true 2.417,1.729 2.781,1.938 0.365,0.208 10 false SST

Using SST, remove the front differential case rear tapered roller bearing (outer race) and differential case shim from the manual transmission case.

SST
09950-60010  (09951-00560)
09950-70010  (09951-07200)


Hide 30.REMOVE TRANSAXLE CASE OIL SEAL

a.
C230553E01
0.068,0.757 0.383,0.944 0.316,0.188 10 SST 0.862,0.842 0.425,0.842 false

Using SST, remove the transaxle case oil seal from the manual transaxle case.

SST
09308-00010  

NOTICE:

Do not damage the installation surfaces of the manual transaxle case.



Hide 41311E 31.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C230554E01
0.124,0.452 0.451,0.632 0.327,0.180 10 SST 1.07,0.54 0.506,0.54 false

Using SST, remove the front differential case front tapered roller bearing (outer race) from the manual transaxle case.

SST
09308-00010  


Hide 33311K 32.REMOVE REAR INPUT SHAFT BEARING SHIM

a.
G020992

Remove the rear input shaft bearing shim from the manual transmission case.


Hide 33321A 33.REMOVE OUTPUT SHAFT REAR BEARING

a.
C310747C01
1.01,1.375 0.833,1.792 0.833,1.792 1.448,1.521 true 2.271,0.583 2.448,0.76 0.177,0.177 10 false *a 0.344,0.688 0.5,0.854 0.156,0.167 10 false *b 0.542,1.781 0.844,1.948 0.302,0.167 10 false SST
*a Turn
*b Hold


Using SST, remove the output shaft rear bearing (outer race) from the manual transmission case.

SST
09527-30010  
09612-65014  (09612-01030, 09612-01050)


Hide 33321H 34.REMOVE REAR OUTPUT SHAFT BEARING SHIM

a.
G020994

Remove the rear output shaft bearing shim from the manual transmission case.