Home › Drivetrain › C551 (MANUAL TRANSMISSION / TRANSAXLE) › INPUT SHAFT › from 2020.07
RM36W0E _52 Drivetrain _091208 C551 MANUAL TRANSMISSION / TRANSAXLE _0432180 INPUT SHAFT A

C551 MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 33311A 1.INSTALL FRONT INPUT SHAFT BEARING

a.
G021247E04
2.733,0.782 3.074,0.983 0.341,0.201 10 SST 2.252,1.495 2.713,0.92 false

Using SST and a press, install a new input shaft front bearing onto the input shaft.

SST
09515-10010  


Hide 33333A 2.INSTALL 3RD GEAR NEEDLE ROLLER BEARING

a.
C233031

Coat the 3rd gear needle roller bearing with gear oil, and install it onto the input shaft.


Hide 33333 3.INSTALL 3RD GEAR

a.
G021248

Coat the 3rd gear with gear oil, and install it onto the input shaft.


Hide 33368G 4.INSTALL 3RD GEAR SYNCHRONIZER RING

a.
G021249

Coat the 3rd gear synchronizer ring with gear oil, and install it onto the 3rd gear.


Hide 33362 5.INSTALL NO. 2 TRANSMISSION CLUTCH HUB

a.
C232584

Install the No. 2 transmission hub sleeve to the No. 2 transmission clutch hub, and then install the 3 No. 2 shifting keys and 2 shifting key springs.

NOTICE:

Assemble the No. 2 transmission hub sleeve and No. 2 transmission clutch hub in the correct orientations shown in the illustration.



b.
G021250E04
0.875,1.906 1.563,1.823 true 0.583,1.823 1.042,2.021 0.458,0.198 10 false SST

Using SST and a press, install the No. 2 transmission hub sleeve to the input shaft.

SST
09506-35010  

NOTICE:
·

Install the No. 2 transmission clutch hub in the correct orientation shown in the illustration.

·

When installing the No. 2 transmission clutch hub, align the cutout of the No. 2 transmission clutch hub with the protrusion of the 3rd gear synchronizer ring.




Hide 33362A 6.INSTALL NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING

a.
G021251C05
0.667,1.323 0.667,1.521 false 0.583,1.521 0.771,1.719 0.188,0.198 10 false *a
*a Alignment Mark


Select a snap ring that allows the minimum axial play.

Standard clearance:

0.1 mm (0.00393 in.) or less.


Snap Ring Thickness:
Part No. Mark Thickness
mm (in.)
90520-32014 A 2.280 (0.0898)
90520-32015 B 2.340 (0.0921)
90520-32016 C 2.400 (0.0945)
90520-32017 D 2.460 (0.0969)
90520-32018 E 2.520 (0.0992)
90520-32019 F 2.580 (0.1016)



b.
G021233

Using a snap ring expander, install the new snap ring onto the input shaft.

NOTICE:

Do not damage the journal surface of the input shaft.



c.

Inspect the 3rd gear thrust clearance and radial clearance (See page Drivetrain>C551 (MANUAL TRANSMISSION / TRANSAXLE)>INPUT SHAFT>DISASSEMBLY).

If either clearance is more than the maximum, check the installation condition of the No. 2 transmission clutch hub and repeat the procedure to select a No. 2 clutch hub setting shaft snap ring.


Hide 33368H 7.INSTALL 4TH GEAR SYNCHRONIZER RING

a.
G021254

Coat the 4th gear synchronizer ring with gear oil and install it to the No. 2 transmission clutch hub.


Hide 33334B 8.INSTALL 4TH GEAR BEARING SPACER

a.
G021255

Coat the 4th gear bearing spacer with gear oil and install it to the input shaft.


Hide 33334A 9.INSTALL 4TH GEAR NEEDLE ROLLER BEARING

a.
C233030

Coat the 4th gear needle roller bearing with gear oil and install it to the input shaft.


Hide 33334 10.INSTALL 4TH GEAR

a.
G021257

Coat the 4th gear with gear oil and install it to the input shaft.


Hide 33346C 11.INSTALL 5TH GEAR THRUST WASHER BALL

a.
G021346

Install the 5th gear thrust washer ball to the input shaft.


Hide 33346B 12.INSTALL 5TH GEAR THRUST WASHER

a.
G021230

Coat the 5th gear thrust washer with gear oil and install it to the input shaft.


Hide 33336C 13.INSTALL 5TH GEAR SHAFT SNAP RING

a.
G021347C06
0.719,1.365 0.719,1.552 false 0.625,1.521 0.833,1.719 0.208,0.198 10 false *a
*a Alignment Mark


Using the table below, select a new 5th gear shaft snap ring that alignment makes the thrust clearance of the 5th gear thrust washer less than 0.1 mm (0.00393 in.).

Plate Shim Thickness:
Part No. Mark Thickness
mm (in.)
90520-29049 1 2.280 (0.0898)
90520-29050 2 2.340 (0.0921)
90520-29052 3 2.400 (0.0945)
90520-29053 4 2.460 (0.0969)
90520-29054 5 2.520 (0.0992)
90520-29055 6 2.580 (0.1016)



b.
G021229

Using a snap ring expander, install the new 5th gear shaft snap ring to the input shaft.

NOTICE:

Do not damage the journal surface of the input shaft.



c.

Inspect the 4th gear thrust clearance and radial clearance (See page Drivetrain>C551 (MANUAL TRANSMISSION / TRANSAXLE)>INPUT SHAFT>DISASSEMBLY).

If either clearance is more than the maximum, repeat the procedure to select a 5th gear shaft snap ring.


Hide 33336B 14.INSTALL 5TH GEAR BEARING SPACER

a.
G021227

Coat the 5th gear bearing spacer with gear oil and install it to the input shaft.


Hide 33336A 15.INSTALL 5TH GEAR NEEDLE ROLLER BEARING

a.
G021226

Coat the 5th gear needle roller bearing with gear oil and install it to the input shaft.


Hide 33336 16.INSTALL 5TH GEAR

a.
G021351

Coat the 5th gear with gear oil and install it to the input shaft.


Hide 33368J 17.INSTALL 5TH GEAR SYNCHRONIZER RING

a.
G021352

Coat the 5th gear synchronizer ring with gear oil and install it to the 5th gear.


Hide 33393 18.INSTALL NO. 3 TRANSMISSION CLUTCH HUB

a.
G021353

Install the No. 3 transmission hub sleeve to the No. 3 transmission clutch hub, and then install the 3 No. 3 shifting keys and 2 No. 1 shifting key springs.

NOTICE:

Assemble the No. 3 transmission hub sleeve, 3 No. 3 shifting keys and No. 3 transmission clutch hub in the correct orientations shown in the illustration.



b.

Install the No. 3 transmission hub sleeve to the input shaft, and then align the 5th gear synchronizer ring slots with No. 3 shifting keys.


c.
G021354E01
0.576,1.702 0.863,1.903 0.287,0.201 10 SST 1.555,1.839 0.954,1.822 false

Using SST and a press, install the No. 3 transmission clutch hub set to the input shaft.

SST
09515-10010  

NOTICE:

Install the No. 3 transmission hub sleeve in the correct orientation as shown in the illustration.



Hide 33311E 19.INSTALL REAR INPUT SHAFT RADIAL BALL BEARING

a.
G021355E01
1.667,1.776 1.954,1.977 0.287,0.201 10 SST 1.306,1.782 1.65,1.879 false

Using SST and a press, install a new rear input shaft radial ball bearing onto the input shaft.

SST
09515-10010  


b.

Inspect the 5th gear thrust clearance and radial clearance (See page Drivetrain>C551 (MANUAL TRANSMISSION / TRANSAXLE)>INPUT SHAFT>DISASSEMBLY).