Home › Vehicle Exterior › ACOUSTIC VEHICLE ALERTING SYSTEM › ACOUSTIC VEHICLE ALERTING SYSTEM › from 2020.07
RM36W0E _59 Vehicle Exterior _091206 ACOUSTIC VEHICLE ALERTING SYSTEM _0432211 ACOUSTIC VEHICLE ALERTING SYSTEM J

ACOUSTIC VEHICLE ALERTING SYSTEM  ACOUSTIC VEHICLE ALERTING SYSTEM  There is No Sound Made  


DESCRIPTION

Based on signals received from each ECU, the vehicle approaching speaker controller outputs warning sounds through the vehicle approaching speaker assembly.

WIRING DIAGRAM

E446512E05
5.594,5.75 6.885,6.26 1.292,0.51 10 false Vehicle Approaching Speaker Assembly 4.5,4.948 4.958,5.146 0.458,0.198 10 false SP+ 6.188,5.229 6.646,5.427 0.458,0.198 10 false - 4.469,6.969 4.927,7.167 0.458,0.198 10 false GND 3.531,7.781 4.813,8.229 1.281,0.448 10 false Vehicle Approaching Speaker Controller 0.781,7.469 2.698,7.76 1.917,0.292 10 false Combination Meter Assembly 0.802,2.365 2.583,2.708 1.781,0.344 10 false Hybrid Vehicle Control ECU 0.844,4.052 2.5,4.542 1.656,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 0.688,5.75 2.792,6.354 2.104,0.604 10 false Skid Control ECU (Brake Actuator Assembly) 1.938,0.896 3,1.135 1.063,0.24 10 false ECU-IGR NO. 1 0.135,0.708 1.521,0.958 1.385,0.25 10 false from IGR-NO. 1 Relay 3.573,0.74 4.031,0.938 0.458,0.198 10 false IG 1.479,8.417 3.333,8.635 1.854,0.219 10 false : CAN Communication Line 3.365,0.625 3.823,0.823 0.458,0.198 10 false 1 3.531,7.615 3.948,7.823 0.417,0.208 10 false A69 4.854,4.854 5.271,5.063 0.417,0.208 10 false 7 4.854,5.156 5.271,5.365 0.417,0.208 10 false 8 4.844,6.844 5.26,7.052 0.417,0.208 10 false 6 5.594,5.583 6.01,5.792 0.417,0.208 10 false A61 6.031,4.854 6.448,5.063 0.417,0.208 10 false 2 6.031,5.135 6.448,5.344 0.417,0.208 10 false 1 6.177,4.948 6.635,5.146 0.458,0.198 10 false + 4.521,5.25 4.979,5.448 0.458,0.198 10 false SP-

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle proximity notification system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the automatic high beam system after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>ACOUSTIC VEHICLE ALERTING SYSTEM>ACOUSTIC VEHICLE ALERTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Trouble Codes.

Body Electrical > Vehicle Proximity Notification System > Trouble Codes
50001 393

b.

Check for DTCs.


Result:
Result Proceed to
DTC B135013 or B135019 is not output A
DTC B135013 or B135019 is output B



A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Proximity Sound (Vehicle Stationary) 0 km/h (0 mph) vehicle proximity warning sound OFF or ON -
Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display
Proximity Sound (Vehicle Stationary)
50004 393 2

Result:
Result Proceed to
The warning sound is produced A
The warning sound is not produced B



A

B

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
a.

Disconnect the A69 vehicle approaching speaker controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A69-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A69-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR