Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422055 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with continuously variable transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1.INSTALL BREATHER PLUG SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the continuously variable transaxle assembly.


a.
C428840

Install the breather plug sub-assembly to the continuously variable transaxle assembly.


Hide 35150B 2.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.
C428839C03
0.521,0.094 0.792,0.333 0.271,0.24 12 false *A 1.625,0.094 1.938,0.333 0.313,0.24 12 false *B
*A for Type A
*B for Type B


for Type A:

i.

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission case plug assembly.

NOTICE:

Ensure that the O-ring is not twisted.



ii.

Install the transmission case plug assembly to the continuously variable transaxle assembly.

NOTICE:

Be careful not to damage the O-ring.




b.

for Type B:

i.

Install the transmission case plug assembly to the continuously variable transaxle assembly.

NOTICE:

Be careful not to damage the O-ring.




Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 3 wire harness clamp brackets to the continuously variable transaxle assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12364B 5.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C434365C01
0.188,1.271 0.708,1.458 0.521,0.188 10 true 1(*a), 4 0.688,0.573 0.833,0.75 0.146,0.177 10 true 3 1.656,1.604 1.802,1.781 0.146,0.177 10 true 2
*a Temporarily Tighten


Install the No. 2 engine moving control rod to the continuously variable transaxle assembly with the 3 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 51201 6.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Install the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


Hide 7.INSTALL CVT TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands and then apply MP grease to the entire periphery of the lip of a new CVT type T oil seal.


b.

Temporarily install the CVT type T oil seal by pressing it to the installation surface of the oil pump housing by hand.

NOTICE:

Be sure to install the CVT type T oil seal in the correct direction.



c.

Clean the CVT type T oil seal contact surface of SST and the area around it.

SST
09223-00010  


d.
C428783C01
1.667,2.583 1.667,2.167 false 0.844,2.667 1.156,2.823 0.313,0.156 10 false *a 1.583,2.594 1.896,2.75 0.313,0.156 10 false SST
*a Depth


Using SST and a hammer, drive the CVT type T oil seal in evenly, until it is even with the side surface of the transaxle housing.

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Drive the CVT type T oil seal in gradually, while visually checking that it is even.

·

After installation, confirm that the CVT type T oil seal has been driven in until it is even with the side surface of the transaxle housing.

·

Wipe any extra grease off with your hand.




Hide 32000A 8.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C428784C01
1.323,0.458 1.823,0.167 true 2.469,0.521 2.771,0.979 true 1.833,0.052 2.146,0.208 0.313,0.156 10 false *a 2.24,0.427 2.427,0.604 0.188,0.177 10 true *b
*a Matchmark
*b Key


Set the key at the top of the drive sprocket and put a matchmark on the transaxle housing.


b.
C429298C01
1.396,0.177 1.552,0.177 1.552,0.177 1.75,0.5 false 1.417,2.021 1.573,2.021 1.573,2.021 1.74,1.667 false 1.25,0.083 1.542,0.313 0.292,0.229 10 false *a 1.26,1.948 1.531,2.125 0.271,0.177 10 false *b
*a Groove
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.

HINT:

The relative positions of the groove (*a) in the sleeve and the setblock will not necessarily be the same as in the illustration.



c.
C429299C02
1.25,0.708 0.448,0.198 0.448,0.198 1.25,0.479 true 2.354,1.365 1.635,1.948 1.635,1.948 2.375,1.063 true 1.49,1.896 1.802,2.052 0.313,0.156 10 false *1 0.271,0.104 0.563,0.281 0.292,0.177 10 false *a
*1 CVT Type T Oil Seal
*a Matchmark


Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT Type T Oil Seal.




d.
C429300C01
1.292,0.417 1.552,0.104 1.552,0.104 1.698,0.104 true 1.271,1.604 1,1.927 1,1.927 0.844,1.927 true 2.365,1.052 1.646,1.958 1.646,1.958 2.365,1.365 true 1.51,1.885 1.74,2.073 0.229,0.188 10 false *1 1.698,0.021 1.958,0.219 0.26,0.198 10 false *a 0.688,1.844 0.948,2.042 0.26,0.198 10 true *a
*1 CVT Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT Type T Oil Seal.




e.
C450689C01
1.313,0.698 0.625,0.229 0.625,0.229 1.333,0.479 true 2.448,1.375 1.5,1.99 1.5,1.99 2.438,1.115 true 1.354,1.927 1.656,2.135 0.302,0.208 10 false *1 0.469,0.115 0.781,0.323 0.313,0.208 10 false *a
*1 CVT Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the groove of the torque converter assembly into the key of the drive sprocket.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the CVT type T oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C435474N01
0.729,0.104 0.885,0.302 0.156,0.198 10 false A

Using a vernier caliper and straightedge, measure the dimension (A) between the set block and the end face of the continuously variable transaxle assembly.

NOTICE:

Make sure to deduct the thickness of the straightedge.



h.
C451164C01
0.573,2.073 0.24,2.417 true 2.646,1.49 2.385,1.573 false 2.865,0.438 3.042,0.563 false 0.906,0.771 1.375,0.406 true 2.698,0.333 2.896,0.5 0.198,0.167 10 false *a 0.052,2.354 0.24,2.521 0.188,0.167 10 false *b 2.906,1.875 3.094,2.042 0.188,0.167 10 false B 1.417,0.323 1.615,0.49 0.198,0.167 10 false *a 2.219,1.51 2.406,1.677 0.188,0.167 10 false *b
*a Engine Assembly Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (B) between the continuously variable transaxle assembly contact surface of the engine*a and the torque converter assembly contact surfaces of the drive plate*b, and check that dimension (B) is larger than dimension (A).

Standard:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 9.INSTALL ENGINE ASSEMBLY

a.
C435476C01
1.823,1.073 2.49,0.74 true 1.74,3.302 2.406,2.969 true 0.271,0.094 0.531,0.271 0.26,0.177 12 false *A 0.396,2.354 0.677,2.542 0.281,0.188 12 false *B 1.052,1.208 1.365,1.365 0.313,0.156 10 false *1 2.531,0.646 2.844,0.802 0.313,0.156 10 false *2 1.083,3.406 1.396,3.563 0.313,0.156 10 false *1 2.448,2.875 2.76,3.031 0.313,0.156 10 false *2
*A for Type A
*B for Type B
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum Grease Amount:

Approximately 1 g (0.0353 oz.)



b.
C435477C01
1.146,0.844 2.583,1.385 2.583,1.385 2.208,0.573 true 2.604,1.302 2.917,1.458 0.313,0.156 10 false *1 2.083,2.479 2.24,2.677 0.156,0.198 10 false A 2.51,4.104 2.667,4.302 0.156,0.198 10 false C 2.177,4.458 2.333,4.656 0.156,0.198 10 false B 0.813,2.74 0.969,2.938 0.156,0.198 10 false C 0.563,3.344 0.719,3.542 0.156,0.198 10 true C 0.813,4.125 0.969,4.323 0.156,0.198 10 true C 1.146,4.438 1.302,4.635 0.156,0.198 10 true C
*1 Knock Pin


Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.


c.

Install the continuously variable transaxle assembly to the engine assembly with the 7 bolts.

Torque:
Bolt (A) : 46 N*m (469 kgf*cm, 34 ft.*lbf)
Bolt (B) : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt (C) : 46 N*m (469 kgf*cm, 34 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.



HINT:
·

Bolt (A), (B): Install from continuously variable transaxle assembly side

·

Bolt (C): Install from engine assembly side




Hide 28100 10.INSTALL STARTER ASSEMBLY (w/ Stop And Start System)

Hide 28100 11.INSTALL STARTER ASSEMBLY (w/o Stop And Start System)

Hide 16290F 12.CONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

Hide 16290F 13.CONNECT NO. 4 WATER BY-PASS HOSE

Hide 89535B 14.INSTALL TCM

NOTICE:

To prevent coolant from entering the TCM through its connector portion, be sure to connect all of the coolant system hoses before installing the TCM.


a.

Install the TCM to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 82121 15.CONNECT ENGINE WIRE

a.

Engage the 3 clamps to connect the engine wire to the front suspension crossmember sub-assembly.


b.

Engage the 3 clamps to connect the engine wire to the continuously variable transaxle assembly.


c.

Connect the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

Connect the No. 3 water by-pass hose assembly.


e.

w/ Stop and Start System:

i.

Connect the oil pump assembly connector and engage the clamp.



f.

Engage the 4 clamps to connect the engine wire to the continuously variable transaxle assembly.

C435478C01
2.635,0.073 2.813,0.24 0.177,0.167 10 true *1 2.938,0.76 3.125,0.927 0.188,0.167 10 true *2 2.948,1.333 3.135,1.49 0.188,0.156 10 true *3 3.719,0.75 3.906,0.906 0.188,0.156 10 true *4 3.083,1.844 3.271,2 0.188,0.156 10 true *5 4.354,1.823 4.542,1.99 0.188,0.167 10 true *6 2.667,2.583 2.854,2.75 0.188,0.167 10 true *7 2.188,2.313 2.375,2.469 0.188,0.156 10 true *8
*1 Transmission Wire Connector *2 Shift Stroke Sensor Connector
*3 Park/Neutral Position Switch Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 TCM Connector *6 Transmission Revolution Sensor (NSS) Connector
*7 Oil Pressure Sensor Connector *8 Transmission Revolution Sensor (NT) Connector
V113147

Install in this Direction - -



g.

Connect the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 89 in.*lbf)


h.

Connect the transmission revolution sensor (NT) connector.


i.

Connect the oil pressure sensor connector.


j.

Connect the transmission revolution sensor (NSS) connector.


k.

Connect the TCM connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the TCM connector makes a click sound.



l.

Connect the transmission revolution sensor (NOUT) connector.


m.

Connect the park/neutral position switch connector.


n.

Connect the shift stroke sensor connector.


o.

Connect the transmission wire connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 32101G 17.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Clean the threads of the 6 drive plate and torque converter assembly setting bolts.


b.
C321585C01
1.729,1.865 2.021,1.865 2.021,1.865 2.094,1.49 false 1.531,1.75 1.844,1.906 0.313,0.156 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper installation of the 6 drive plate and torque converter assembly setting bolts, apply adhesive to the 6 drive plate and torque converter assembly setting bolts and install them within 10 minutes of adhesive application.



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 18.INSTALL FLYWHEEL HOUSING UNDER COVER

a.
C435479C01
0,0 0,0 false
V113147

Install in this Direction


Install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 20.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE