Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › HYBRID TRANSAXLE FLUID › from 2020.07
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0421990 HYBRID TRANSAXLE FLUID N

P910 HYBRID TRANSMISSION / TRANSAXLE  HYBRID TRANSAXLE FLUID  ADJUSTMENT  


PROCEDURE

Hide 51451A 1.REMOVE CENTER ENGINE UNDER COVER (w/ Cover)

Hide 2.DRAIN HYBRID TRANSAXLE FLUID

a.
C429453

Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly.


b.
C429454

Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the hybrid vehicle transaxle assembly and drain the hybrid transaxle fluid.


c.

Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


d.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.

HINT:

Reuse the old gasket as the filler plug will be removed again.



Hide 3.ADD HYBRID TRANSAXLE FLUID

a.
C429455C04
2.417,1.125 2.719,0.781 false 2.75,0.656 2.99,0.865 0.24,0.208 10 false *a 3.146,1.708 3.375,1.917 0.229,0.208 10 false *b
*a Filler Nozzle
*b 0 to 8 mm (0 to 0.315 in.)


Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly.


b.

Add hybrid transaxle fluid until the hybrid transaxle fluid level is between 0 to 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. [#]

NOTICE:
·

When adding hybrid transaxle fluid, make sure that the vehicle is level.

·

Use Toyota Genuine ATF WS.

Using transmission fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transmission of your vehicle.

·

Be sure to fully insert the filler nozzle into the filler plug opening.

·

Be sure to add hybrid transaxle fluid slowly. If hybrid transaxle fluid is added quickly, the hybrid transaxle fluid may hit internal parts and bounce back, resulting in hybrid transaxle fluid coming out of the filler plug opening.

·

Be sure to directly check that the hybrid transaxle fluid level is within the specified range.

·

Driving the vehicle with an insufficient or excessive amount of hybrid transaxle fluid may damage the hybrid vehicle transaxle assembly.



Hybrid Transaxle Fluid Standard Capacity (for Reference):

2.6 liters (2.7 US qts, 2.3 Imp. qts)



c.

After adding hybrid transaxle fluid, leave the vehicle for 30 seconds so that the hybrid transaxle fluid surface can become still again, and then check that the hybrid transaxle fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. (If the hybrid transaxle fluid level is low, repeat this procedure from step [#].)

NOTICE:

After adding hybrid transaxle fluid, make sure to check the hybrid transaxle fluid level.



d.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.

HINT:

Reuse the old gasket as the filler plug will be removed again.



Hide 5.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 51451A 6.INSTALL CENTER ENGINE UNDER COVER (w/ Cover)