Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) Y

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:

*: Use the GTS.


PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS

Result:
Proceed to
NEXT



NEXT

3.CHECK DTC, FREEZE FRAME DATA AND VEHICLE CONTROL HISTORY*
3.CHECK DTC, FREEZE FRAME DATA AND VEHICLE CONTROL HISTORY*
a.

Check and record DTCs and Freeze Frame Data.

i.

Check and record DTCs.

Chassis > Brake > Trouble Codes
50001 435
Chassis > Steering Angle Sensor > Trouble Codes
50001 445

ii.

Check and record Freeze Frame Data.



b.

Clear the DTCs and Freeze Frame Data.

Chassis > Brake > Clear DTCs
50002 435
Chassis > Steering Angle Sensor > Clear DTCs
50002 445

c.

Reconfirm the DTCs.

i.

Reconfirm the DTCs based on the recorded DTCs and Freeze Frame Data.

Chassis > Brake > Trouble Codes
50001 435
Chassis > Steering Angle Sensor > Trouble Codes
50001 445
HINT:
·

When CAN communication system DTCs are output, repair the CAN communication system first.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If DTCs related to momentary interruptions are output, perform troubleshooting for those DTCs first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>CHECK FOR INTERMITTENT PROBLEMS

·

If the GTS cannot communicate with the skid control ECU (brake actuator assembly), inspect the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If there is no response from the skid control ECU (brake actuator assembly), inspect the IGR circuit and +BS circuit of the skid control ECU (brake actuator assembly).

Click here

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>TERMINALS OF ECU





d.

Check the Vehicle Control History.

Chassis > Brake > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55
Chassis > Steering Angle Sensor > Utility
Tester Display
Vehicle Control History (RoB)
50005 445 55

Result:
Result Proceed to
DTCs are output A
DTCs are not output (problem symptom occurs) B
DTCs are not output (problem symptom does not occurs) C
DTCs are not output (vehicle control history occurs) D



A

4.REPAIR CIRCUITS INDICATED BY OUTPUT DTCS*

B

5.PROBLEM SYMPTOMS TABLE

C

D

PERFORM TROUBLESHOOTING AND REPAIR REGARDING VEHICLE CONTROL HISTORY*

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>VEHICLE CONTROL HISTORY

HINT:

After performing troubleshooting and repair regarding vehicle control history, clear the vehicle control history.



4.REPAIR CIRCUITS INDICATED BY OUTPUT DTCS*

Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC*
5.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
The problem symptoms are not listed in the problem symptoms table. A
The problem symptoms are listed in the problem symptoms table. B



A

6.PERFORM TROUBLESHOOTING BASED ON PROBLEM SYMPTOM*

B

11.REPAIR PERFORM TROUBLESHOOTING BASED ON PROBLEM SYMPTOM*
7.REPAIR OR REPLACEMENT
CAUTION:

Refer to the precautions before performing adjustment, repair or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>PRECAUTION


Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC*
8.CLEAR DTC*
a.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435
Chassis > Steering Angle Sensor > Clear DTCs
50002 445

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC*
9.RECONFIRM DTC*
a.

Check if the same DTCs are output.

Chassis > Brake > Trouble Codes
50001 435
Chassis > Steering Angle Sensor > Trouble Codes
50001 445

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

10.CONFIRMATION TEST*

B

10.CONFIRMATION TEST*
Result:
Proceed to
NEXT



NEXT

END

11.REPAIR PERFORM TROUBLESHOOTING BASED ON PROBLEM SYMPTOM*

Result:
Proceed to
NEXT



NEXT

9.RECONFIRM DTC*