Refer to DTC C050618
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C05061F | Right Front Wheel Speed Sensor Circuit Intermittent | ·
The speed sensor signal is excessively noisy. ·
The calculated change in wheel speed is more than 980 m/s2 for 5*1 or 20*2 seconds or more. ·
The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2 for 5*1 or 20*2 seconds or more. ·
When the vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 second for 5*1 or 20*2 seconds or more. |
·
Front speed sensor RH ·
Front speed sensor rotor RH (front axle hub sub-assembly RH) |
Brake |
*1: The stop light switch assembly is OFF.
*2: The stop light switch assembly is ON.
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
The front speed sensor rotor RH is incorporated into the front axle hub sub-assembly RH.
If the front speed sensor rotor RH needs to be replaced, replace the front axle hub sub-assembly RH.
Pre-procedure1
Remove the front speed sensor RH.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
Procedure1
Check the front speed sensor RH.
The front speed sensor RH tip is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor RH, clean the front speed sensor RH.
If the front speed sensor RH is damaged, replace the front speed sensor RH with a new one.
Post-procedure1
None
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the component with the front speed sensor rotor RH.
Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF Made)>REMOVAL
The front speed sensor rotor RH is incorporated into the front axle hub sub-assembly RH.
If the front speed sensor rotor RH needs to be replaced, replace it together with the front axle hub sub-assembly RH.
Procedure1
Check the front speed sensor rotor RH.
The front speed sensor rotor RH is free of scratches, oil, and foreign matter.
If there is oil or foreign matter on the front speed sensor rotor RH, clean the front speed sensor rotor RH.
Do not use parts cleaner when cleaning the front speed sensor rotor RH.
If the front speed sensor rotor RH is damaged, replace the front speed sensor rotor RH with a new one.
Post-procedure1
None
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The front speed sensor rotor RH is damaged.) | B |
| NG (There is foreign matter on the front speed sensor rotor RH.) | C |
A
B
C
Clean the front speed sensor rotor RH.
Do not use parts cleaner when cleaning the front speed sensor rotor RH.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform a Dealer Mode (Signal Check) inspection sensor check.
| Tester Display |
|---|
| Signal Check |
Check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for front speed sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor RH (front axle hub sub-assembly RH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF Made)>REMOVAL
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Operate the GTS to read the DTCs.
Check if the same DTC is output.
Post-procedure1
Turn the ignition switch off.
| Result | Proceed to |
|---|---|
| C05061F is not output | A |
| C05061F is output | B |
A
B
for front speed sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor RH (front axle hub sub-assembly RH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF Made)>REMOVAL
When cleaning the front speed sensor RH, make sure to clean the installation hole before installation.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform a Dealer Mode (Signal Check) inspection sensor check.
| Tester Display |
|---|
| Signal Check |
Check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for front speed sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor RH (front axle hub sub-assembly RH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF Made)>REMOVAL
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Operate the GTS to read the DTCs.
Check if the same DTC is output.
Post-procedure1
Turn the ignition switch off.
| Result | Proceed to |
|---|---|
| C05061F is not output | A |
| C05061F is output | B |
A
B
for front speed sensor RH: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for front speed sensor rotor RH (front axle hub sub-assembly RH): Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF Made)>REMOVAL