Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  C050618  Right Front Wheel Speed Sensor Circuit Current Below Threshold  


DESCRIPTION

Each speed sensor detects wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS control.

The speed sensor detects the magnetic fields of the speed sensor rotor as it rotates and outputs a pulse signal.

The frequency of the pulse varies in accordance with the rotational speed of the speed sensor rotor and the system uses this to determine the wheel speed.

HINT:

The following example shows a pulse signal that is output when the wire harness connectors are connected to the speed sensors and skid control ECU (brake actuator assembly).

C223506E21
1.281,1.063 1.281,0.708 1.281,0.708 1.073,0.708 false 0.167,0.615 1.354,0.927 1.188,0.313 10 false Speed Sensor 4.948,1.938 5.719,2.344 0.771,0.406 10 false High speed 4.021,1.938 4.729,2.313 0.708,0.375 10 false Low speed 0.917,2.177 2.344,2.583 1.427,0.406 10 false Speed Sensor Rotor


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C050618 Right Front Wheel Speed Sensor Circuit Current Below Threshold This wheel speed sensor signal electrical current value is less than the threshold value for 0.14 second or more.
·

Front speed sensor RH

·

Speed sensor installation

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


Brake

WIRING DIAGRAM

C400496E35
5.26,1.042 5.76,1.208 0.5,0.167 10 false FR+ 1.635,1.135 2.073,1.302 0.438,0.167 10 false FR+ 1.635,1.802 2.073,1.99 0.438,0.188 10 false FR- 5.26,1.708 5.719,1.906 0.458,0.198 10 false FR- 4.917,3 5.417,3.198 0.5,0.198 10 false A37 4.917,3.167 7.073,3.656 2.156,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 4.958,1.042 5.292,1.292 0.333,0.25 10 false 27 4.958,1.719 5.271,2.031 0.313,0.313 10 false 26 2.021,1.688 2.406,1.958 0.385,0.271 10 false 1 2.021,1.021 2.375,1.292 0.354,0.271 10 false 2 0.75,2.417 2.417,2.667 1.667,0.25 10 false Front Speed Sensor RH 0.75,2.25 1.219,2.448 0.469,0.198 10 false A23

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A23 front speed sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

d.

Turn the ignition switch to ON.


Procedure1

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A23-2 (FR+) - A23-1 (FR-) Ignition switch ON 11 to 14 V



Post-procedure1

f.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE ACTUATOR ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE ACTUATOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-1 (FR-) or A37-26 (FR-) - Body ground Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR RH - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-2 (FR+) or A37-27 (FR+) - A23-1 (FR-) or A37-26 (FR-) Always 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FR WHEEL SPEED)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (FR WHEEL SPEED)

Pre-procedure1

a.

Reconnect the A37 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the A23 front speed sensor RH connector.


Procedure1

c.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
FR Wheel Speed
50003 435 13

d.

Drive the vehicle and perform a road test.

OK:

The values change in accordance with the operation of the vehicle.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Post-procedure1

e.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG