FREEZE FRAME DATA
Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.
CHECK FREEZE FRAME DATA WHEN DTC WAS STORED (BRAKE)
Freeze frame data is stored when a DTC is output.
Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.
Operate the GTS to enter the Trouble Codes.
Select a DTC to display the freeze frame data.
Check the freeze frame data for the output DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Master Cylinder Sensor 1 | Master cylinder pressure sensor pressure (value detected by ECU) | Min.: -1.00 MPa
Max.: 23.99 MPa |
Brake pedal released: -1.00 to 0.00 MPa | Reading increases when brake pedal is depressed |
| M/C Sensor Grade | Master cylinder pressure sensor change (value detected by ECU) | Min.: -30 MPa/s
Max.: 225 MPa/s |
Brake pedal released or pedal held at constant position: 0 MPa/s | When brake pedal is being operated: Changes in proportion with the pedal movement speed |
| Lateral G | Lateral G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Yaw Rate Sensor Value | Yaw rate sensor | Min.: -128°/s
Max.: 127°/s |
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Steering Angle Value | Steering sensor | Min.: -3276.8°
Max.: 3276.7° |
Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0° |
- |
| MT Voltage Value | ABS motor drive voltage value | Min.: 0.0 V
Max.: 25.5 V |
Vehicle Stopped: 0 V | Changes in proportion to auxiliary battery voltage
|
| Solenoid Power Supply Voltage | Solenoid power supply voltage value | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | - |
| Engine Revolutions | Engine speed | Min.: 0 rpm
Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
| Throttle Opening Angle | Throttle valve opening angle | Min.: 0°
Max.: 125° |
- | During throttle valve operation: Changes in proportion with the valve movement |
| Accelerator Opening Angle | Accelerator pedal opening angle | Min.: 0°
Max.: 125° |
Accelerator pedal released: 0° | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%
Max.: 127.5% |
Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Real Engine Torque | Powertrain drive-torque | Min.: -1024.000 Nm
Max.: 1023.000 Nm |
- | - |
| Power Train Driving force | Powertrain drive torque | Min.: -327680 N
Max.: 327670 N |
- | - |
| Gear Position | Gear position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / 7th / 8th / 9th / 10th / P/N / R | Actual gear position | - |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd /3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| TRC(TRAC)/VSC OFF Mode | TRC/VSC off mode | Normal mode (TRC (TRAC) ON/VSC ON) / TRC (TRAC) OFF mode (TRC (TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC (TRAC) OFF/VSC OFF) | Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode |
- |
| Brake Hold Control Mode | - | Out of control mode / Pressure hold mode /Pressure release mode / EPB lock mode | - | Cannot be used |
| FR Target Oil Pressure | Front wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| FL Target Oil Pressure | Front wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RR Target Oil Pressure | Rear wheel RH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| RL Target Oil Pressure | Rear wheel LH target oil pressure | Min.: 0.0 MPa
Max.: 20.0 MPa |
- | Different according to target oil pressure of each wheel |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph) |
Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed Grade | Vehicle acceleration | Min.: -25.105 m/s2
Max.: 24.908 m/s2 |
Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
| Vehicle Stop Time from IG ON | Time vehicle stopped after ignition switch turned to ON | Min.: 0 s
Max.: 1275 s |
- | - |
| Travel Distance from IG ON | Driving time after ignition switch turned to ON | Min.: 0 s
Max.: 1275 s |
- | - |
| IG Switch | Ignition switch ON status | OFF / ON | - | - |
| Downhill Assist Control SW | - | OFF / ON | - | Cannot be used |
| Stop Light SW | Stop light switch assembly (STP terminal input) | OFF / ON | OFF: Brake pedal released
ON: Brake pedal depressed |
|
| Parking Brake SW | Parking brake switch | OFF / ON | OFF: Parking brake released
ON: Parking brake applied |
- |
| Brake Pedal Load Sensing SW | - | OFF / ON | - | Cannot be used |
| Brake Hold Switch | - | OFF / ON | - | Cannot be used |
| Stop Light Relay | Stop light switch assembly (STP2 terminal input) | OFF / ON | OFF: Stop light switch assembly (STP2 terminal input) OFF
ON: Stop light switch assembly (STP2 terminal input) ON |
|
| Inspection Mode | Inspection mode | OFF / ON | OFF: Normal mode
ON: Inspection mode |
|
| TRC(TRAC) Control | TRC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Engine Control | TRC engine control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| TRC(TRAC) Brake Control | TRC brake control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel LH ABS control status | Out of controlling / Under Controlling | Out of controlling: During not control
Under Controlling: During control |
- |
| HAB Control | High power assist brake status | OFF / ON | OFF: During not control
ON: During control |
- |
| Fail Status | Brake booster failure status | OFF / ON | OFF: During not control
ON: During control |
- |
| Fail Control | Failure control status | OFF / ON | OFF: During not control
ON: During control |
- |
| BA Ctrl Status | BA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| PBA Ctrl Status | PBA control status | OFF / ON | OFF: During not control
ON: During control |
- |
| Stop Light Relay State for ECU Control | Stop light switch assembly (STPO terminal output)(value detected by ECU) | OFF / ON | OFF: Stop light switch assembly not operating
ON: Stop light switch assembly operating |
- |
| Engine Stop by Stop and Start System | Engine stopped by stop and start system status (for ECU control) | OFF / ON | OFF: Engine not stopped by stop and start control
ON: Engine stopped by stop and start control |
w/ Stop and Start System |
| Solenoid State for ECU Control | ABS solenoid relay status (for ECU control) | OFF / ON | OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating |
- |
| Motor State for ECU Control | ABS motor relay status (for ECU control) | OFF / ON | OFF: ABS motor relay not operating
ON: ABS motor relay operating |
- |
| Operation History of IG OFF while Vehicle is moving | History of ignition switch turned off when vehicle is in motion | OFF / ON | OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher |
- |
| Buzzer | Meter buzzer | OFF / ON | OFF: Buzzer off
ON: Buzzer on |
- |
| Dealer Mode | Dealer Mode (Signal Check mode or Calibration mode) status | OFF / ON | OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode) |
|
| Zero Point Memory State of Steering Angle Sensor | Steering sensor zero point memorization status | Zero point is not memorized / Zero point is memorized | - |
|
| TRC(TRAC)/VSC OFF SW | VSC OFF switch (combination switch assembly) (CSW terminal input) | OFF / ON | OFF: VSC OFF switch (combination switch assembly) OFF
ON: VSC OFF switch (combination switch assembly) ON |
|
| IGP_PT1 | IGP_PT1 status | OFF / ON | OFF: IGP_PT1 OFF
ON: IGP_PT1 ON |
- |
| IGP_PT2 | IGP_PT2 status | OFF / ON | OFF: IGP_PT2 OFF
ON: IGP_PT2 ON |
- |
| FR Wheel | Rotatory direction for front wheel RH | Forward / Back | - | - |
| FL Wheel | Rotatory direction for front wheel LH | Forward / Back | - | - |
| RR Wheel | Rotatory direction for rear wheel RH | Forward / Back | - | - |
| RL Wheel | Rotatory direction for rear wheel RH | Forward / Back | - | - |
| EFI Communication Open | ECM communication open detection | Under intermittent / Normal | Under intermittent: ECM communication invalid state detected
Normal: ECM communication invalid state not detected |
Related DTC: U010087 |
| Yaw Rate Open | Yaw rate sensor open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
Related DTC: U012587 |
| Deceleration Open | Acceleration sensor open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
Related DTC: U012587 |
| Steering Open | Steering sensor open detection | Under intermittent / Normal | Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected |
Related DTC: U012687 |
| Clutch Stroke | - | Min.: 0.000 V
Max.: 5.000 V |
- | Cannot be used |
| +BS Voltage | +BS terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
| +BM Voltage | +BM terminal voltage value (value detected by ECU) | Min.: 0.0 V
Max.: 25.5 V |
Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to auxiliary battery voltage
|
*1: for entering inspection mode: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY
*2: for performing Dealer Mode (Signal Check): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>TEST MODE PROCEDURE
*3: for entering Dealer Mode (Calibration): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY
CLEAR FREEZE FRAME DATA (BRAKE)
Clearing the DTC will also clear the Freeze Frame Data.
Clear the DTC and Freeze Frame Data.
CHECK FREEZE FRAME DATA WHEN DTC WAS STORED (STEERING ANGLE SENSOR)
Freeze frame data is stored when a DTC is output.
Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.
Operate the GTS to enter the Trouble Codes.
Select a DTC to display the freeze frame data.
Check the freeze frame data for the output DTC.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| Total Distance Traveled - Unit | Total Distance Traveled unit | km / mile | - | - |
CLEAR FREEZE FRAME DATA (STEERING ANGLE SENSOR)
Clearing the DTC will also clear the Freeze Frame Data.
Clear the DTC and Freeze Frame Data.