Home › Engine / Hybrid System › M15A-FXE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2020.07–2021.11
RM36W0E _51 Engine / Hybrid System _088540 M15A-FXE INTAKE / EXHAUST _0421800 EXHAUST MANIFOLD A

M15A-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 51447D 1.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 57543C 2.REMOVE CENTER NO. 1 FLOOR BRACE (w/ Cover)

a.
A468521

Remove the 2 nuts and center No. 1 floor brace from the vehicle.


Hide 17410 3.REMOVE FRONT EXHAUST PIPE ASSEMBLY

CAUTION:
·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



a.
A463768

Disconnect the No. 2 air fuel ratio sensor connector.


b.

Disengage the clamp.


c.

Remove the 4 bolts and 4 compression springs and disconnect the front exhaust pipe assembly from the exhaust manifold and tail exhaust pipe assembly.

A463769


d.

Remove the front exhaust pipe assembly from the 3 exhaust pipe supports.


e.

Remove the 2 exhaust pipe gaskets from the exhaust manifold and front exhaust pipe assembly.


Hide 58151 4.REMOVE NO. 1 FRONT FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A463770

Remove the nut and No. 1 front floor heat insulator from the vehicle body.


Hide 82715W 6.REMOVE WIRING HARNESS CLAMP BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.

Disengage the clamp and remove the bolt and wiring harness clamp bracket from the cylinder head sub-assembly.


Hide 25760 7.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY (w/ Differential Pressure Sensor)

Hide 25733A 8.REMOVE NO. 1 VACUUM PIPE (w/ Differential Pressure Sensor)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A468356

Remove the nut.


b.

Remove the No. 1 vacuum pipe from the exhaust manifold.


Hide 17167 9.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A463771

Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.


Hide 17118 10.REMOVE MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A463772

Remove the bolt, nut and manifold stay from the exhaust manifold and cylinder block sub-assembly.


Hide 17141 11.REMOVE EXHAUST MANIFOLD

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A463773

Remove the 6 nuts and exhaust manifold from the cylinder head sub-assembly.


b.
A463774

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 17168 12.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A463775

Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold.