Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › AIR FUEL RATIO SENSOR (for Sensor 2) › 2020.07–2021.11
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0422228 AIR FUEL RATIO SENSOR(for Sensor 2) A

M15A-FXE ENGINE CONTROL  AIR FUEL RATIO SENSOR(for Sensor 2)  INSTALLATION  


PROCEDURE

Hide 89467C 1.INSTALL NO. 2 AIR FUEL RATIO SENSOR

HINT:

Perform "Inspection After Repair" after replacing the No. 2 air fuel ratio sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A433385C01
2.792,1.198 2.448,0.771 true 0.865,1.729 1.115,1.948 0.25,0.219 10 true *a 2.708,1.219 3.115,1.417 0.406,0.198 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the No. 2 air fuel ratio sensor to the front exhaust pipe assembly.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the No. 2 air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




b.
A463082

Engage the 2 wire harness clamp.

NOTICE:

Make sure the white tube is between the wires.



c.

Connect the No. 2 air fuel ratio sensor connector.


Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.
A463084C02
0.177,0.281 0.49,0.479 0.313,0.198 10 false *a 1.823,0.271 2.135,0.469 0.313,0.198 10 false *b 0.385,1.313 0.698,1.51 0.313,0.198 10 false *c 2,1.292 2.313,1.49 0.313,0.198 10 false *c
*a Correct
*b Incorrect
*c Standard Position


Install the wire harness clamp bracket to the No. 2 air fuel ratio sensor.

NOTICE:

Aline the edge of the wire harness clamp bracket and No. 2 air fuel ratio sensor as shown in the illustration.



b.

Engage the guide to connect the wire harness to the wire harness clamp bracket.


Hide 57543C 3.INSTALL CENTER NO. 1 FLOOR BRACE (for TMMF Made)

a.

w/ Cover:

i.

Install the front floor center brace to the vehicle body with the 2 nuts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)



Hide 51447D 4.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMMF Made)

Hide 51447D 5.INSTALL CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)

Hide 7.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the No. 2 air fuel ratio sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION