Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER › 2020.07–2020.09
RM36W0E _53 Suspension _087264 REAR SUSPENSION _0417605 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side

·

The following procedure is for the LH side.



PROCEDURE

Hide 48760B 1.INSTALL REAR SUSPENSION SUPPORT ASSEMBLY

a.

Install the rear suspension support assembly to the rear shock absorber assembly.


Hide 48540 2.TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

a.

Insert the upper end of the rear shock absorber assembly with rear suspension support assembly into the vehicle body.


b.

Temporarily install the rear shock absorber assembly to the rear axle beam assembly with the bolt and nut.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.


HINT:

Insert the bolt with the threaded end facing the inside of the vehicle.



Hide 48755 3.INSTALL REAR SUSPENSION SUPPORT

a.

Install the rear suspension support to the rear shock absorber assembly.

NOTICE:
C429095C02
0.729,0.51 1.042,0.708 0.313,0.198 10 false *a 2.563,0.49 2.875,0.688 0.313,0.198 10 false *b
*a Correct
*b Incorrect


Make sure that the rear suspension support is correctly installed as shown in the illustration.



Hide 48597A 4.INSTALL REAR SHOCK ABSORBER CUSHION RETAINER

a.

Install the rear shock absorber cushion retainer to the rear shock absorber assembly


b.
C484095C01
2.344,0.771 2.656,0.969 0.313,0.198 10 false *a 2.719,2.677 3.031,2.875 0.313,0.198 10 true *b 0.344,2.271 0.656,2.469 0.313,0.198 10 true *c
*a Torque Wrench Fulcrum Length
*b Turn
*c Hold


Width Across Flats 17mm nut:

While using a 5 mm hexagon socket wrench to hold the rear shock absorber assembly in place, use a ball joint lock nut wrench to tighten the nut until the rear shock absorber cushion retainer is seated to the collar of the rear suspension support assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 155.5 mm (6.12 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.))) : 7.7 N*m (79 kgf*cm, 68 in.*lbf))




c.
C484096C01
1.458,2.24 1.813,1.917 true 2.354,0.781 2.667,0.979 0.313,0.198 10 false *a 1.188,2.24 1.646,2.438 0.458,0.198 10 true SST 2.729,2.542 3.042,2.74 0.313,0.198 10 true *b 0.333,2.333 0.646,2.531 0.313,0.198 10 true *c
*a Torque Wrench Fulcrum Length
*b Turn
*c Hold


Width Across Flats 14mm nut:

While using a 5 mm hexagon socket wrench to hold the rear shock absorber assembly in place, use SST to tighten the nut until the rear shock absorber cushion retainer is seated to the collar of the rear suspension support assembly.

SST
09729-00140  

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a SST(fulcrum length of 200 mm (7.87 in.))+ torque wrench (fulcrum length of 162 mm (6.38 in.))) : 6.7 N*m (68 kgf*cm,59 in.*lbf))




d.

for Double Nut Type:

i.

Install a new nut (upper nut) onto the lower nut.


ii.
C439902C01
0.083,0.906 0.396,1.063 0.313,0.156 10 false *A 0.104,2.073 0.417,2.229 0.313,0.156 10 false *B
*A for TMC Made
*B for TMMF Made


Hold the lower nut and tighten the upper nut against it.

Torque:
for TMC Made : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)
for TMMF Made : 15 N*m (153 kgf*cm, 11 ft.*lbf)



Hide 64715C 5.INSTALL DECK SIDE TRIM COVER

a.

Engage the 2 guides and 3 claws to install the deck side trim cover.


Hide 6.INSTALL REAR WHEEL

Hide 48540 8.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

a.

Fully tighten the rear shock absorber assembly (lower side) with the bolt while keeping the nut from rotating.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 10.PERFORM INITIALIZATION

Parking support brake system (Click here)
Parking assist monitor system (Click here)