Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT › 2020.07–2020.09
RM36W0E _53 Suspension _087257 ALIGNMENT / HANDLING DIAGNOSIS _0417578 REAR WHEEL ALIGNMENT G

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT  INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the rear wheel alignment procedure are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Rear wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)

PROCEDURE

Hide 3.INSPECT CAMBER

NOTICE:

Inspect while the vehicle is unloaded.


a.
C107736C10
2.052,1.26 2.375,1.26 false 2.406,1.167 2.656,1.385 0.25,0.219 10 *a
*a Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle) (for TMC Made):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
M15A-FKS M/T 175/70R14
185/60R15
185/55R16
-1°03' +/- 0°30' (-1.05° +/- 0.50°) 0°33' (0.55°) or less
CVT 175/70R14
185/60R15
185/55R16
-1°03' +/- 0°30' (-1.05° +/- 0.50°)
M15A-FXE - 175/70R14
185/60R15
185/55R16
-1°03' +/- 0°30' (-1.05° +/- 0.50°)


Camber (Unloaded Vehicle) (for TMMF Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
1KR-FE M/T 185/65R15
195/55R16
-0°57' +/- 0°30' (-0.95° +/- 0.50°) 0°33' (0.55°) or less
M15A-FKS M/T 185/65R15
195/55R16
205/45R17
-0°57' +/- 0°30' (-0.95° +/- 0.50°)
CVT 185/65R15
195/55R16
205/45R17
-0°57' +/- 0°30' (-0.95° +/- 0.50°)
M15A-FXE - 185/65R15 -0°57' +/- 0°30' (-0.95° +/- 0.50°)
195/55R16
205/45R17
-0°58' +/- 0°30' (-0.97° +/- 0.50°)


Camber (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
1KR-FE M/T 185/65R15 -0°53' +/- 0°30' (-0.88° +/- 0.50°) 0°33' (0.55°) or less
M15A-FKS M/T 185/65R15 -0°53' +/- 0°30' (-0.88° +/- 0.50°)
CVT 185/65R15 -0°53' +/- 0°30' (-0.88° +/- 0.50°)
M15A-FXE - 185/65R15 -0°54' +/- 0°30' (-0.90° +/- 0.50°)


Camber (Unloaded Vehicle) (for TMMF Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Camber Inclination Right-left Difference
1KR-FE M/T 185/65R15 -0°57' +/- 0°30' (-0.95° +/- 0.50°) 0°33' (0.55°) or less
M15A-FKS M/T 185/65R15 -0°57' +/- 0°30' (-0.95° +/- 0.50°)
CVT 185/65R15 -0°57' +/- 0°30' (-0.95° +/- 0.50°)
M15A-FXE - 185/65R15 -0°57' +/- 0°30' (-0.95° +/- 0.50°)


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.



Hide 4.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N (for CVT, Hybrid Transaxle).


c.

Release the parking brake and move the shift lever to neutral (for Manual Transaxle).


d.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


e.
C188968C02
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


f.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.



g.
C188969C02
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle) (for TMC Made):
Engine Transaxle Tire Size Specified Condition
M15A-FKS M/T 175/70R14
185/60R15
C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.2 +/- 3.0 mm (0.165 +/- 0.118 in.)
185/55R16 C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.)
CVT 175/70R14
185/60R15
C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.2 +/- 3.0 mm (0.165 +/- 0.118 in.)
185/55R16 C + D: 0°23' +/- 0°17' (0.38° +/- 0.28°)
B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.)
M15A-FXE - 175/70R14
185/60R15
C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°)
B - A: 4.3 +/- 3.0 mm (0.169 +/- 0.118 in.)
185/55R16 C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°)
B - A: 4.4 +/- 3.0 mm (0.173 +/- 0.118 in.)


Toe-in (Unloaded Vehicle) (for TMMF Made (except Rough Road Area Specification)):
Engine Transaxle Tire Size Specified Condition
1KR-FE M/T 185/65R15
195/55R16
C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°)
B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.)
M15A-FKS M/T 185/65R15
195/55R16
205/45R17
C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°)
B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.)
CVT 185/65R15
195/55R16
205/45R17
C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°)
B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.)
M15A-FXE - 185/65R15
195/55R16
C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°)
B - A: 4.6 +/- 3.1 mm (0.187 +/- 0.122 in.)
205/45R17 C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°)
B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.)


Toe-in (Unloaded Vehicle) (for TMMF Made (for Rough Road Area, Height Up Specification)):
Engine Transaxle Tire Size Specified Condition
1KR-FE M/T 185/65R15 C + D: 0°21' +/- 0°17' (0.35° +/- 0.28°)
B - A: 3.9 +/- 3.1 mm (0.154 +/- 0.122 in.)
M15A-FKS M/T 185/65R15 C + D: 0°21' +/- 0°17' (0.35° +/- 0.28°)
B - A: 3.9 +/- 3.1 mm (0.154 +/- 0.122 in.)
CVT 185/65R15 C + D: 0°21' +/- 0°17' (0.35° +/- 0.28°)
B - A: 3.9 +/- 3.1 mm (0.154 +/- 0.122 in.)
M15A-FXE - 185/65R15 C + D: 0°21' +/- 0°17' (0.35° +/- 0.28°)
B - A: 4.0 +/- 3.1 mm (0.157 +/- 0.122 in.)


Toe-in (Unloaded Vehicle) (for TMMF Made (for Rough Road Area except Height Up Specification)):
Engine Transaxle Tire Size Specified Condition
1KR-FE M/T 185/65R15 C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°)
B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.)
M15A-FKS M/T 185/65R15 C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°)
B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.)
CVT 185/65R15 C + D: 0°24' +/- 0°17' (0.40° +/- 0.28°)
B - A: 4.5 +/- 3.1 mm (0.177 +/- 0.122 in.)
M15A-FXE - 185/65R15 C + D: 0°25' +/- 0°17' (0.42° +/- 0.28°)
B - A: 4.6 +/- 3.1 mm (0.187 +/- 0.122 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.


Hide 5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.INSPECT AND ADJUST HEADLIGHT AIMING

HINT:

These procedures are to be performed when suspension or tires components have been removed or replaced.