Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.07–2020.09
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0422141 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Microphone Circuit  


DESCRIPTION

·

The radio and display receiver assembly, telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the telephone transceiver assembly sends power to telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the telephone transceiver assembly.*

*: w/ Telephone Transceiver Assembly



WIRING DIAGRAM

E402703E12
5.76,1.365 6.375,1.563 0.615,0.198 10 false SNS2 1.719,1.26 2.135,1.458 0.417,0.198 10 false SNS2 1.677,1.677 2.135,1.854 0.458,0.177 10 false MACC 1.688,2 2.146,2.177 0.458,0.177 10 false MCO+ 1.719,2.354 2.177,2.531 0.458,0.177 10 false MCO- 5.781,1.771 6.24,1.948 0.458,0.177 10 false MACC 5.771,2.073 6.146,2.302 0.375,0.229 10 false MIN+ 5.771,2.417 6.146,2.646 0.375,0.229 10 false MIN- 5.771,2.792 6.271,3.021 0.5,0.229 10 false SGND 3.833,2.75 4.333,2.979 0.5,0.229 10 false * 0.552,3.063 1.958,3.521 1.406,0.458 10 false Telephone Microphone Assembly 0.573,2.906 1.979,3.365 1.406,0.458 10 false MC 0.333,4.01 1.938,4.333 1.604,0.323 10 false Map Light Assembly 0.333,3.854 0.677,4.042 0.344,0.188 10 false V7 5.438,3.802 5.781,3.99 0.344,0.188 10 false H80 5.438,3.979 7.115,4.344 1.677,0.365 10 false Radio and Display Receiver Assembly 1.552,1.26 1.688,1.438 0.135,0.177 10 false 1 1.542,1.667 2,1.844 0.458,0.177 10 false 5 1.542,1.99 2,2.167 0.458,0.177 10 false 3 1.552,2.354 2.01,2.531 0.458,0.177 10 false 2 2.177,1.26 2.406,1.458 0.229,0.198 10 false 13 2.177,1.667 2.427,1.906 0.25,0.24 10 false 16 2.188,2.01 2.469,2.24 0.281,0.229 10 false 15 2.188,2.344 2.427,2.573 0.24,0.229 10 false 14 5.5,2.688 5.844,2.875 0.344,0.188 10 false 24 5.49,1.979 5.833,2.167 0.344,0.188 10 false 21 5.49,2.344 5.833,2.531 0.344,0.188 10 false 22 5.51,1.635 5.854,1.823 0.344,0.188 10 false 23 5.51,1.24 5.854,1.427 0.344,0.188 10 false 25 2.458,4.469 4.167,4.667 1.708,0.198 10 false *: Shielded 1.083,1.365 1.5,1.563 0.417,0.198 10 false SNS2 1.052,1.75 1.51,1.927 0.458,0.177 10 false MACC 1.135,2.083 1.594,2.26 0.458,0.177 10 false MIC+ 1.146,2.417 1.604,2.594 0.458,0.177 10 false MIC- 0.167,0.115 2.552,0.354 2.385,0.24 12 false for TMC Made:

E402703E13
5.76,1.365 6.375,1.563 0.615,0.198 10 false SNS2 1.719,1.26 2.135,1.458 0.417,0.198 10 false SNS2 1.677,1.677 2.135,1.854 0.458,0.177 10 false MACC 1.688,2 2.146,2.177 0.458,0.177 10 false MCO+ 1.719,2.354 2.177,2.531 0.458,0.177 10 false MCO- 5.781,1.771 6.24,1.948 0.458,0.177 10 false MACC 5.771,2.073 6.146,2.302 0.375,0.229 10 false MIN+ 5.771,2.417 6.146,2.646 0.375,0.229 10 false MIN- 5.771,2.792 6.271,3.021 0.5,0.229 10 false SGND 3.833,2.75 4.333,2.979 0.5,0.229 10 false * 0.552,3.063 1.958,3.521 1.406,0.458 10 false Telephone Microphone Assembly 0.573,2.906 1.979,3.365 1.406,0.458 10 false MC 0.333,4.01 1.938,4.333 1.604,0.323 10 false Map Light Assembly 0.333,3.854 0.677,4.042 0.344,0.188 10 false V6 5.438,3.802 5.781,3.99 0.344,0.188 10 false H80 5.438,3.979 7.115,4.344 1.677,0.365 10 false Radio and Display Receiver Assembly 1.552,1.26 1.688,1.438 0.135,0.177 10 false 1 1.542,1.667 2,1.844 0.458,0.177 10 false 5 1.542,1.99 2,2.167 0.458,0.177 10 false 3 1.552,2.354 2.01,2.531 0.458,0.177 10 false 2 2.177,1.26 2.406,1.458 0.229,0.198 10 false 15 2.177,1.667 2.427,1.906 0.25,0.24 10 false 2 2.188,2.01 2.469,2.24 0.281,0.229 10 false 3 2.188,2.344 2.427,2.573 0.24,0.229 10 false 4 5.5,2.688 5.844,2.875 0.344,0.188 10 false 24 5.49,1.979 5.833,2.167 0.344,0.188 10 false 21 5.49,2.344 5.833,2.531 0.344,0.188 10 false 22 5.51,1.635 5.854,1.823 0.344,0.188 10 false 23 5.51,1.24 5.854,1.427 0.344,0.188 10 false 25 2.458,4.469 4.167,4.667 1.708,0.198 10 false *: Shielded 1.083,1.365 1.5,1.563 0.417,0.198 10 false SNS2 1.052,1.75 1.51,1.927 0.458,0.177 10 false MACC 1.135,2.083 1.594,2.26 0.458,0.177 10 false MIC+ 1.146,2.417 1.604,2.594 0.458,0.177 10 false MIC- 0.135,0.094 6.99,0.333 6.854,0.24 12 false for TMMF Made without Telephone Transceiver Assembly:

E402702E26
5.729,1.188 6.344,1.385 0.615,0.198 10 false SNS2 5.74,1.833 6.354,2.031 0.615,0.198 10 false MIN+ 5.74,2.26 6.354,2.458 0.615,0.198 10 false MIN- 5.771,2.802 6.385,3 0.615,0.198 10 false SGND 5.104,2.698 5.719,2.896 0.615,0.198 10 false * 0.115,0.094 5.406,0.417 5.292,0.323 12 false for TMMF Made with Telephone Transceiver Assembly: 0.521,2.906 1,3.115 0.479,0.208 10 false MC 0.5,3.063 1.927,3.469 1.427,0.406 10 false Telephone Microphone Assembly 1.646,1.094 2.094,1.271 0.448,0.177 10 false SNS2 1.615,1.677 2.115,1.854 0.5,0.177 10 false MACC 1.625,2 2.125,2.177 0.5,0.177 10 false MCO+ 1.656,2.375 2.156,2.552 0.5,0.177 10 false MCO- 1.469,2.01 1.75,2.188 0.281,0.177 10 false 3 1.479,1.094 1.76,1.271 0.281,0.177 10 false 1 1.469,1.656 1.75,1.833 0.281,0.177 10 false 5 1.479,2.344 1.76,2.521 0.281,0.177 10 false 2 2.094,1.094 2.385,1.302 0.292,0.208 10 false 15 2.083,1.979 2.375,2.188 0.292,0.208 10 false 3 2.094,1.646 2.385,1.854 0.292,0.208 10 false 2 2.094,2.344 2.385,2.552 0.292,0.208 10 false 4 3.375,1.76 3.875,1.938 0.5,0.177 10 false MCVD 3.375,2.094 3.875,2.271 0.5,0.177 10 false MCI+ 3.375,2.417 3.875,2.594 0.5,0.177 10 false MCI- 3.385,2.792 3.885,2.969 0.5,0.177 10 false SGND 0.281,3.833 0.688,4.073 0.406,0.24 10 false V6 0.271,4.031 2.5,4.292 2.229,0.26 10 false Map Light Assembly 3.208,3.604 5.438,3.865 2.229,0.26 10 false Telephone Transceiver Assembly 3.198,3.417 5.427,3.677 2.229,0.26 10 false H85 5.375,3.938 7.104,4.365 1.729,0.427 10 false Radio and Display Receiver Assembly 5.375,3.792 7.104,4.219 1.729,0.427 10 false H80 5.458,1.083 6.073,1.281 0.615,0.198 10 false 25 5.458,1.729 6.073,1.927 0.615,0.198 10 false 21 5.458,2.146 6.073,2.344 0.615,0.198 10 false 22 5.479,2.635 6.094,2.833 0.615,0.198 10 false 24 4.135,1.823 4.635,2 0.5,0.177 10 false MCO+ 4.146,2.229 4.646,2.406 0.5,0.177 10 false MCO- 3.177,1.656 3.677,1.833 0.5,0.177 10 false 5 3.167,1.99 3.667,2.167 0.5,0.177 10 false 6 3.177,2.344 3.677,2.521 0.5,0.177 10 false 7 3.125,2.677 3.625,2.854 0.5,0.177 10 false 23 4.646,1.719 5.146,1.896 0.5,0.177 10 false 16 4.667,2.156 5.167,2.333 0.5,0.177 10 false 32 2.438,4.385 4.667,4.646 2.229,0.26 10 false *: Shielded 2.573,2.729 3.188,2.927 0.615,0.198 10 false * 0.99,1.208 1.438,1.385 0.448,0.177 10 false SNS2 0.969,1.76 1.469,1.938 0.5,0.177 10 false MACC 1.042,2.094 1.542,2.271 0.5,0.177 10 false MIC+ 1.042,2.417 1.542,2.594 0.5,0.177 10 false MIC-

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made without Telephone Transceiver Assembly B
for TMMF Made with Telephone Transceiver Assembly C



A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

C

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the V7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-25 (SNS2) - V7-13 (SNS2) Always Below 1 Ω
H80-23 (MACC) - V7-16 (MACC) Always Below 1 Ω
H80-21 (MIN+) - V7-15 (MCO+) Always Below 1 Ω
H80-22 (MIN-) - V7-14 (MCO-) Always Below 1 Ω
H80-25 (SNS2) or V7-13 (SNS2) - Body ground Always 10 kΩ or higher
H80-23 (MACC) or V7-16 (MACC) - Body ground Always 10 kΩ or higher
H80-21 (MIN+) or V7-15 (MCO+) - Body ground Always 10 kΩ or higher
H80-22 (MIN-) or V7-14 (MCO-) - Body ground Always 10 kΩ or higher
H80-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the H80 radio and display receiver assembly connector.


b.

Connect the V7 map light assembly connector.


c.
E439833C01
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 true 2.188,2.885 1.927,2.146 true 2.813,2.604 2.052,2.156 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.583,0.771 1.896,0.969 0.313,0.198 10 false H80 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.094,2.896 2.729,3.115 0.635,0.219 10 false MACC 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H80-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-24 (SGND) - Body ground Always Below 1 Ω
H80-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the H80 radio and display receiver assembly connector.


b.

Connect the V7 map light assembly connector.


c.

Turn the ignition switch to ACC.


d.
E437720C01
1.51,0.146 1.885,0.396 0.375,0.25 0.656,1.906 1.125,1.219 true 1.208,1.917 1.219,1.219 true 0.427,1.948 1.042,2.146 0.615,0.198 10 false MCO+ 1.615,0.198 2.229,0.396 0.615,0.198 10 false V7 2.958,3.25 3.406,3.438 0.448,0.188 10 false GND 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a 1.104,1.958 1.719,2.156 0.615,0.198 10 false MCO-
*a Component with harness connected
(Map Light Assembly)


Connect an oscilloscope to terminals 15 (MCO+) and 14 (MCO-) of the V7 map light assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V7-15 (MCO+) - V7-14 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

6.INSPECT MAP LIGHT ASSEMBLY
6.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the MC telephone microphone assembly connector.


c.
E437721C02
1.458,0.396 1.844,0.646 0.385,0.25 1.5,2.823 1.885,3.073 0.385,0.25 1.813,2.146 1.385,1.635 true 1.427,2.125 1.167,1.615 true 0.448,2.073 0.969,1.615 true 0.99,2.167 1.073,1.625 true 1.146,3.823 1.427,3.406 true 1.552,3.813 1.563,3.406 true 2,3.823 1.698,3.417 true 2.469,3.656 2.01,3.406 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.125,2.458 0.458,2.656 0.333,0.198 10 false *b 1.354,2.198 1.854,2.417 0.5,0.219 10 false MCO- 0.896,2.198 1.375,2.406 0.479,0.208 10 false MCO+ 1.573,0.458 2.052,0.667 0.479,0.208 10 false V7 1.604,2.885 2.083,3.094 0.479,0.208 10 false MC 1.823,2.188 2.302,2.396 0.479,0.208 10 false SNS2 0.25,2.125 0.75,2.344 0.5,0.219 10 false MACC 2.49,3.708 2.969,3.917 0.479,0.208 10 false MACC 1.958,3.865 2.438,4.073 0.479,0.208 10 false MIC+ 1.479,3.875 1.958,4.083 0.479,0.208 10 false MIC- 1,3.865 1.479,4.073 0.479,0.208 10 false SNS2
*a Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-13 (SNS2) - MC-1 (SNS2) Always Below 1 Ω
V7-16 (MACC) - MC-5 (MACC) Always Below 1 Ω
V7-15 (MCO+) - MC-3 (MIC+) Always Below 1 Ω
V7-14 (MCO-) - MC-2 (MIC-) Always Below 1 Ω
V7-13 (SNS2) - Body ground Always 10 kΩ or higher
V7-16 (MACC) - Body ground Always 10 kΩ or higher
V7-15 (MCO+) - Body ground Always 10 kΩ or higher
V7-14 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the V6 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-25 (SNS2) - V6-15 (SNS2) Always Below 1 Ω
H80-23 (MACC) - V6-2 (MACC) Always Below 1 Ω
H80-21 (MIN+) - V6-3 (MCO+) Always Below 1 Ω
H80-22 (MIN-) - V6-4 (MCO-) Always Below 1 Ω
H80-25 (SNS2) or V6-15 (SNS2) - Body ground Always 10 kΩ or higher
H80-23 (MACC) or V6-2 (MACC) - Body ground Always 10 kΩ or higher
H80-21 (MIN+) or V6-3 (MCO+) - Body ground Always 10 kΩ or higher
H80-22 (MIN-) or V6-4 (MCO-) - Body ground Always 10 kΩ or higher
H80-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the H80 radio and display receiver assembly connector.


b.

Connect the V7 map light assembly connector.


c.
E439833C01
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 true 2.188,2.885 1.927,2.146 true 2.813,2.604 2.052,2.156 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.583,0.771 1.896,0.969 0.313,0.198 10 false H80 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.094,2.896 2.729,3.115 0.635,0.219 10 false MACC 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H80-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-24 (SGND) - Body ground Always Below 1 Ω
H80-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

9.INSPECT MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the H80 radio and display receiver assembly connector.


b.

Connect the V6 map light assembly connector.


c.

Turn the ignition switch to ACC.


d.
E445959C04
1.51,0.146 1.885,0.396 0.375,0.25 2.208,1.813 1.792,1.135 true 2.479,0.625 1.917,1.063 true 2.271,1.74 2.885,1.938 0.615,0.198 10 false MCO- 1.604,0.188 2.219,0.385 0.615,0.198 10 false V6 2.958,3.219 3.406,3.406 0.448,0.188 10 false GND 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a 2.51,0.531 3.125,0.729 0.615,0.198 10 false MCO+
*a Component with harness connected
(Map Light Assembly)


Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the V6 map light assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V6-3 (MCO+) - V6-4 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

10.INSPECT MAP LIGHT ASSEMBLY
10.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the MC telephone microphone assembly connector.


c.
E445960C01
1.458,0.396 1.844,0.646 0.385,0.25 1.5,2.823 1.885,3.073 0.385,0.25 2.292,2.042 1.865,1.531 true 1.719,1.479 1.167,0.927 true 1.99,1.469 2.51,1.01 true 1.104,2.125 1.406,1.646 true 1.146,3.823 1.427,3.406 true 1.552,3.813 1.563,3.406 true 2,3.823 1.698,3.417 true 2.469,3.656 2.01,3.406 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.125,2.458 0.458,2.656 0.333,0.198 10 false *b 0.708,0.813 1.208,1.031 0.5,0.219 10 false MCO- 2.333,1.969 2.813,2.177 0.479,0.208 10 false MCO+ 1.552,0.438 2.031,0.646 0.479,0.208 10 false V6 1.604,2.885 2.083,3.094 0.479,0.208 10 false MC 0.677,2.052 1.156,2.26 0.479,0.208 10 false SNS2 2.542,0.906 3.042,1.125 0.5,0.219 10 false MACC 2.49,3.708 2.969,3.917 0.479,0.208 10 false MACC 1.958,3.865 2.438,4.073 0.479,0.208 10 false MIC+ 1.479,3.875 1.958,4.083 0.479,0.208 10 false MIC- 1,3.865 1.479,4.073 0.479,0.208 10 false SNS2
*a Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-15 (SNS2) - MC-1 (SNS2) Always Below 1 Ω
V6-2 (MACC) - MC-5 (MACC) Always Below 1 Ω
V6-3 (MCO+) - MC-3 (MIC+) Always Below 1 Ω
V6-4 (MCO-) - MC-2 (MIC-) Always Below 1 Ω
V6-15 (SNS2) - Body ground Always 10 kΩ or higher
V6-2 (MACC) - Body ground Always 10 kΩ or higher
V6-3 (MCO+) - Body ground Always 10 kΩ or higher
V6-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the V6 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-25 (SNS2) - V6-15 (SNS2) Always Below 1 Ω
H80-25 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Disconnect the H85 telephone transceiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-21 (MIN+) - H85-16 (MCO+) Always Below 1 Ω
H80-22 (MIN-) - H85-32 (MCO-) Always Below 1 Ω
H80-21 (MIN+) - Body ground Always 10 kΩ or higher
H80-22 (MIN-) - Body ground Always 10 kΩ or higher
H80-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H85 telephone transceiver assembly connector.


b.

Disconnect the V6 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-5 (MCVD) - V6-7 (MACC) Always Below 1 Ω
H85-6 (MCI+) - V6-6 (MCO+) Always Below 1 Ω
H85-7 (MCI-) - V6-5 (MCO-) Always Below 1 Ω
H85-5 (MCVD) - Body ground Always 10 kΩ or higher
H85-6 (MCI+) - Body ground Always 10 kΩ or higher
H85-7 (MCI-) - Body ground Always 10 kΩ or higher
H85-23 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the H85 telephone transceiver assembly connector.


E447076C01
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 true 2.813,2.604 2.052,2.156 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.583,0.76 1.896,0.958 0.313,0.198 10 false H80 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-24 (SGND) - Body ground Always Below 1 Ω
H80-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.INSPECT TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

15.INSPECT TELEPHONE TRANSCEIVER ASSEMBLY
a.

Connect the H85 telephone transceiver assembly connector.


b.
E447077C01
1.521,0.594 2.021,0.844 0.5,0.25 2.24,1.698 2.615,1.073 true 2.198,2.531 2.281,1.833 true 2.792,2.438 2.417,1.719 true 1.625,0.615 2.052,0.844 0.427,0.229 10 false H85 2.604,0.885 3.052,1.125 0.448,0.24 10 false MCI- 0.198,0.177 0.51,0.375 0.313,0.198 10 false *a 2.656,2.479 3.104,2.719 0.448,0.24 10 false MCVD 2.01,2.583 2.458,2.823 0.448,0.24 10 false SGND
*a Component with harness connected
(Telephone Transceiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H85-5 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-7 (MCI-) - Body ground Always Below 1 Ω
H85-23 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

16.CHECK MAP LIGHT ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E445959C05
1.51,0.146 1.885,0.396 0.375,0.25 2.208,1.813 1.792,1.135 true 2.479,0.625 1.917,1.063 true 2.271,1.74 2.885,1.938 0.615,0.198 10 false MCO- 1.604,0.188 2.219,0.385 0.615,0.198 10 false V6 2.958,3.219 3.406,3.406 0.448,0.188 10 false GND 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a 2.51,0.531 3.125,0.729 0.615,0.198 10 false MCO+
*a Component with harness connected
(Map Light Assembly)


Remove the map light assembly with the connector(s) still connected.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the V6 map light assembly connector.


c.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V6-3 (MCO+) - V6-4 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

17.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

18.INSPECT MAP LIGHT ASSEMBLY
17.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
E428332C13
1.5,0.229 1.906,0.49 0.406,0.26 0.896,1.135 0.667,0.427 true 0.563,1.979 0.938,1.24 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.552,0.271 2.01,0.469 0.458,0.198 10 false H85 0.323,2.042 0.938,2.24 0.615,0.198 10 false MCO- 0.188,0.333 0.802,0.531 0.615,0.198 10 false MCO+ 2.823,3.458 3.24,3.656 0.417,0.198 10 false GND
*a Component with harness connected
(Telephone Transceiver Assembly)


Remove the telephone transceiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Connect an oscilloscope to terminal H85-16 (MCO+) and H85-32 (MCO-).


c.

Turn the ignition switch to ACC.


d.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H85-16 (MCO+) - H85-32 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Ignition switch ACC

2.

Sound is input to the telephone microphone assembly when the user is closer than 125 mm from the telephone microphone assembly sound holes in the roof headlining holder cover.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

18.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the MC telephone microphone assembly connector.


c.
E445960C01
1.458,0.396 1.844,0.646 0.385,0.25 1.5,2.823 1.885,3.073 0.385,0.25 2.292,2.042 1.865,1.531 true 1.719,1.479 1.167,0.927 true 1.99,1.469 2.51,1.01 true 1.104,2.125 1.406,1.646 true 1.146,3.823 1.427,3.406 true 1.552,3.813 1.563,3.406 true 2,3.823 1.698,3.417 true 2.469,3.656 2.01,3.406 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.125,2.458 0.458,2.656 0.333,0.198 10 false *b 0.708,0.813 1.208,1.031 0.5,0.219 10 false MCO- 2.333,1.969 2.813,2.177 0.479,0.208 10 false MCO+ 1.552,0.438 2.031,0.646 0.479,0.208 10 false V6 1.604,2.885 2.083,3.094 0.479,0.208 10 false MC 0.677,2.052 1.156,2.26 0.479,0.208 10 false SNS2 2.542,0.906 3.042,1.125 0.5,0.219 10 false MACC 2.49,3.708 2.969,3.917 0.479,0.208 10 false MACC 1.958,3.865 2.438,4.073 0.479,0.208 10 false MIC+ 1.479,3.875 1.958,4.083 0.479,0.208 10 false MIC- 1,3.865 1.479,4.073 0.479,0.208 10 false SNS2
*a Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-15 (SNS2) - MC-1 (SNS2) Always Below 1 Ω
V6-2 (MACC) - MC-5 (MACC) Always Below 1 Ω
V6-3 (MCO+) - MC-3 (MIC+) Always Below 1 Ω
V6-4 (MCO-) - MC-2 (MIC-) Always Below 1 Ω
V6-15 (SNS2) - Body ground Always 10 kΩ or higher
V6-2 (MACC) - Body ground Always 10 kΩ or higher
V6-3 (MCO+) - Body ground Always 10 kΩ or higher
V6-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY