Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
69760B
1.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
Engage the guide to install the front door inside locking cable assembly to the front door lock assembly.
69760B
2.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
Engage the guide to install the front door inside locking cable assembly to the front door lock assembly.
69720D
3.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
Engage the guide to install the front door lock remote control cable assembly to the front door lock assembly.
|
Install in this Direction |
Engage the claws as shown in the illustration.
69720D
4.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
Engage the guide to install the front door lock remote control cable assembly to the front door lock assembly.
|
Install in this Direction |
Engage the claws as shown in the illustration.
69040A
5.INSTALL FRONT DOOR LOCK ASSEMBLY
When reusing a removed front door lock assembly, replace the door lock wiring harness seal with a new one.
Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.
Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock assembly.
Apply MP grease to the sliding parts of the front door lock assembly.
When reusing the front door lock assembly:
Install a new door lock wiring harness seal to the front door lock assembly.
Connect the front door lock open rod as shown in the illustration.
Make sure that the front door lock open rod is securely connected to the front door lock assembly.
Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.
Connect the connector.
6.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
69220
7.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)
67404F
8.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
68151C
9.INSTALL FRONT DOOR GLASS RUN
68102
10.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
67832
11.INSTALL FRONT DOOR SERVICE HOLE COVER
67856B
12.INSTALL FRONT DOOR PANEL PROTECTOR
67838A
13.INSTALL FRONT DOOR VENT SEAL
68172A
14.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP
67602
15.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
67656
16.INSTALL FRONT DOOR TRIM GARNISH
74231
17.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
74232
18.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
67492A
19.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH
20.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
for 1KR-FE:
Click hereGeneral>MAINTENANCE>1KR-FE AUXILIARY BATTERY>INSTALLATION
21. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
22.INITIALIZE POWER WINDOW CONTROL SYSTEM
23.INSPECT POWER WINDOW OPERATION