1.ADJUST COMPRESSOR OIL
When replacing the compressor with motor assembly with a new one, gradually discharge the inert gas from the service valve, and drain the following amount of oil from the new compressor with motor assembly before installation.
Drain the oil 30 cc (1.01 fl.oz) from a new compressor with motor assembly.
If a new compressor with motor assembly is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.
Be sure to use ND-OIL 11 or equivalent compressor oil. If any compressor oil other than ND-OIL 11 is used, compressor with motor assembly insulation performance may decrease, resulting in leakage of electric power.
88370
2.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY
Temporarily install the compressor with motor assembly with the 4 bolts.
Tighten the 4 bolts to install the cooler compressor with motor assembly as shown in the illustration.
| *a | Connector A |
| *b | Connector B |
Connect the connector B.
Remove the protective tape wrapped around connector A, and as shown in the illustration, connect connector A and lower the green lock to lock it securely.
Make sure to wear insulating gloves.
Make sure that the connector is connected securely.
88711
3.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.
ND-OIL 11 or equivalent
Install the O-ring to the No. 1 cooler refrigerant discharge hose.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the No. 1 cooler refrigerant discharge hose to the compressor with motor assembly with the bolt.
88704
4.CONNECT SUCTION HOSE SUB-ASSEMBLY
Remove the vinyl tape from the suction hose sub-assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor with motor assembly.
ND-OIL 11 or equivalent
Install the O-ring to the suction hose sub-assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the suction hose sub-assembly to the compressor with motor assembly with the bolt.
51451A
5.INSTALL CENTER ENGINE UNDER COVER (w/ Engine Under Cover Assembly)
G3834
6.INSTALL SERVICE PLUG GRIP
7.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
8.WARM UP COMPRESSOR
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
9.INSPECT FOR REFRIGERANT LEAK
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT