Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _089448 PRE-COLLISION _0424816 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U030051  Internal Control Module Software Incompatibility Not Programmed  U030057  Internal Control Module Software Incompatibility Invalid / Incompatible Software Component  


DESCRIPTION

for Gasoline Model:
·

The millimeter wave radar sensor assembly receives vehicle information (Conv/HV/EV) or vehicle information (transmission type) from the ECM via the CAN communication line.

·

If the millimeter wave radar sensor assembly cannot confirm the vehicle information (Conv/HV/EV) or vehicle information (transmission type) sent from the ECM, the millimeter wave radar sensor assembly stores DTC U030051.

·

If the vehicle information (Conv/HV/EV) or vehicle information (transmission type) stored in the millimeter wave radar sensor assembly does not match the vehicle information sent from the ECM, the millimeter wave radar sensor assembly stores DTC U030057.


for HV Model:
·

The millimeter wave radar sensor assembly receives vehicle information (Conv/HV/EV) or vehicle information (transmission type) from the hybrid vehicle control ECU via the CAN communication line.

·

If the millimeter wave radar sensor assembly cannot confirm the vehicle information (Conv/HV/EV) or vehicle information (transmission type) sent from the hybrid vehicle control ECU, the millimeter wave radar sensor assembly stores DTC U030051.

·

If the vehicle information (Conv/HV/EV) or vehicle information (transmission type) stored in the millimeter wave radar sensor assembly does not match the vehicle information sent from the hybrid vehicle control ECU, the millimeter wave radar sensor assembly stores DTC U030057.


DTC No. Detection Item DTC Detection Condition Trouble Area
U030051 Internal Control Module Software Incompatibility Not Programmed
for Gasoline Model:

When the ignition switch is ON for 3 seconds or more, the millimeter wave radar sensor assembly cannot confirm the vehicle information (Conv/HV/EV) or vehicle information (transmission type) sent from the ECM for approximately 3 seconds or more.


for HV Model:

When the ignition switch is ON for 3 seconds or more, the millimeter wave radar sensor assembly cannot confirm the vehicle information (Conv/HV/EV) or vehicle information (transmission type) sent from the hybrid vehicle control ECU for approximately 3 seconds or more.


for Gasoline Model:
·

SFI system

·

Millimeter wave radar sensor assembly

·

ECM


for HV Model:
·

Hybrid control system

·

Millimeter wave radar sensor assembly

·

Hybrid vehicle control ECU


U030057 Internal Control Module Software Incompatibility Invalid / Incompatible Software Component
for Gasoline Model:

When the ignition switch is ON for 3 seconds or more, the vehicle information (Conv/HV/EV) or vehicle information (transmission type) stored in the millimeter wave radar sensor assembly does not match the vehicle information sent from the ECM for approximately 1 second or more.


for HV Model:

When the ignition switch is ON for 3 seconds or more, the vehicle information (Conv/HV/EV) or vehicle information (transmission type) stored in the millimeter wave radar sensor assembly does not match the vehicle information sent from the hybrid vehicle control ECU for approximately 1 second or more.


for Gasoline Model:
·

SFI system

·

Millimeter wave radar sensor assembly

·

ECM


for HV Model:
·

Hybrid control system

·

Millimeter wave radar sensor assembly

·

Hybrid vehicle control ECU



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

for Gasoline Model:

Before replacing the ECM, refer to Service Bulletin.


·

for HV Model:

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Gasoline Model A
for HV Model B



A

2.CONFIRM MODEL

B

11.CHECK FOR DTCs
2.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 1KR-FE A
for M15A-FKS B



A

3.CHECK FOR DTCs

B

7.CHECK FOR DTCs
3.CHECK FOR DTCs
a.

Using the GTS, check for SFI system DTCs.

HINT:

If DTC U030051 or U030057 is output by the pre-collision system, it is possible that SFI system DTCs have been stored, so perform troubleshooting for the SFI system.


Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
SFI system DTCs are not output A
SFI system DTCs are output B



A

4.CHECK FOR DTCs (HEALTH CHECK)

B

4.CHECK FOR DTCs (HEALTH CHECK)
a.

Using the GTS, perform the Health Check.


b.

Check for DTCs.

OK:

ECUs other than the millimeter wave radar sensor assembly do not output specification information mismatch DTCs related to the ECM.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (VEHICLE INFORMATION (Conv/HV/EV))

NG

5.READ VALUE USING GTS (VEHICLE INFORMATION (Conv/HV/EV))
a.

Using the GTS, read the Data List.

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (Conv/HV/EV) Vehicle information (Conv/HV/EV) Unknown / Conv / HV/EV Unknown: Vehicle information not confirmed
Conv: Conventional
HV/EV: Hybrid vehicle
-
Body Electrical > Pre-Collision System > Data List
Tester Display
Vehicle Information (Conv/HV/EV)
50003 432 24
HINT:
·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification do not match, there is a malfunction in the specification information stored by the millimeter wave radar sensor assembly. Therefore, replace the millimeter wave radar sensor assembly.

·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.




Result:
Result Proceed to
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications do not match A
"Unknown" is displayed
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications match B



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

6.READ VALUE USING GTS (VEHICLE INFORMATION (TRANSMISSION TYPE))
6.READ VALUE USING GTS (VEHICLE INFORMATION (TRANSMISSION TYPE))
a.

Using the GTS, read the Data List.

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (Transmission Type) Vehicle Information (Transmission Type) MT / AT / CVT / MMT / SMT / HV/EV - AT / Unknown Displays the type of transmission -
Body Electrical > Pre-Collision System > Data List
Tester Display
Vehicle Information (Transmission Type)
50003 432 36
HINT:
·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification do not match, there is a malfunction in the specification information stored by the millimeter wave radar sensor assembly. Therefore, replace the millimeter wave radar sensor assembly.

·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.




Result:
Result Proceed to
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications do not match A
"Unknown" is displayed
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications match B



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

7.CHECK FOR DTCs
a.

Using the GTS, check for SFI system DTCs.

HINT:

If DTC U030051 or U030057 is output by the pre-collision system, it is possible that SFI system DTCs have been stored, so perform troubleshooting for the SFI system.


Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
SFI system DTCs are not output A
SFI system DTCs are output B



A

8.CHECK FOR DTCs (HEALTH CHECK)

B

8.CHECK FOR DTCs (HEALTH CHECK)
a.

Using the GTS, perform the Health Check.


b.

Check for DTCs.

OK:

ECUs other than the millimeter wave radar sensor assembly do not output specification information mismatch DTCs related to the ECM.



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (VEHICLE INFORMATION (Conv/HV/EV))

NG

9.READ VALUE USING GTS (VEHICLE INFORMATION (Conv/HV/EV))
a.

Using the GTS, read the Data List.

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (Conv/HV/EV) Vehicle information (Conv/HV/EV) Unknown / Conv / HV/EV Unknown: Vehicle information not confirmed
Conv: Conventional
HV/EV: Hybrid vehicle
-
Body Electrical > Pre-Collision System > Data List
Tester Display
Vehicle Information (Conv/HV/EV)
50003 432 24
HINT:
·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification do not match, there is a malfunction in the specification information stored by the millimeter wave radar sensor assembly. Therefore, replace the millimeter wave radar sensor assembly.

·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.




Result:
Result Proceed to
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications do not match A
"Unknown" is displayed
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications match B



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

10.READ VALUE USING GTS (VEHICLE INFORMATION (TRANSMISSION TYPE))
10.READ VALUE USING GTS (VEHICLE INFORMATION (TRANSMISSION TYPE))
a.

Using the GTS, read the Data List.

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (Transmission Type) Vehicle Information (Transmission Type) MT / AT / CVT / MMT / SMT / HV/EV - AT / Unknown Displays the type of transmission -
Body Electrical > Pre-Collision System > Data List
Tester Display
Vehicle Information (Transmission Type)
50003 432 36
HINT:
·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification do not match, there is a malfunction in the specification information stored by the millimeter wave radar sensor assembly. Therefore, replace the millimeter wave radar sensor assembly.

·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.




Result:
Result Proceed to
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications do not match A
"Unknown" is displayed
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications match B



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

11.CHECK FOR DTCs
a.

Using the GTS, check for hybrid control system DTCs.

HINT:

If DTC U030051 or U030057 is output by the pre-collision system, it is possible that hybrid control system DTCs have been stored, so perform troubleshooting for the hybrid control system.


Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
Hybrid control system DTCs are not output A
Hybrid control system DTCs are output B



A

12.CHECK FOR DTCs (HEALTH CHECK)

B

12.CHECK FOR DTCs (HEALTH CHECK)
a.

Using the GTS, perform a health check.


b.

Check for DTCs.

OK:

ECUs other than the millimeter wave radar sensor assembly do not output specification information mismatch DTCs related to the hybrid vehicle control ECU.



Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (VEHICLE INFORMATION (Conv/HV/EV)

NG

13.READ VALUE USING GTS (VEHICLE INFORMATION (Conv/HV/EV)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (Conv/HV/EV) Vehicle information (Conv/HV/EV) Unknown / Conv / HV/ EV Unknown: Vehicle information not confirmed
Conv: Conventional
HV/EV: Hybrid vehicle
-
Body Electrical > Pre-Collision System > Data List
Tester Display
Vehicle Information (Conv/HV/EV)
50003 432 24
HINT:
·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification do not match, there is a malfunction in the specification information stored by the millimeter wave radar sensor assembly. Therefore, replace the millimeter wave radar sensor assembly.

·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification match, a hybrid vehicle control ECU with different specifications may be installed. Therefore, replace the hybrid vehicle control ECU.




Result:
Result Proceed to
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications do not match A
"Unknown" is displayed
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications match B



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

14.READ VALUE USING GTS (VEHICLE INFORMATION (TRANSMISSION TYPE))
14.READ VALUE USING GTS (VEHICLE INFORMATION (TRANSMISSION TYPE))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Pre-Collision System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Information (Transmission Type) Vehicle Information (Transmission Type) MT / AT / CVT / MMT / SMT / HV/EV - AT / Unknown Displays the type of transmission -
Body Electrical > Pre-Collision System > Data List
Tester Display
Vehicle Information (Transmission Type)
50003 432 36
HINT:
·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification do not match, there is a malfunction in the specification information stored by the millimeter wave radar sensor assembly. Therefore, replace the millimeter wave radar sensor assembly.

·

When the specification stored by the millimeter wave radar sensor assembly and the vehicle specification match, a hybrid vehicle control ECU with different specifications may be installed. Therefore, replace the hybrid vehicle control ECU.




Result:
Result Proceed to
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications do not match A
"Unknown" is displayed
Vehicle information stored in millimeter wave radar sensor assembly and actual vehicle specifications match B



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B