Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2020.07–2021.04
RM36W0E _56 Audio / Visual / Telematics _091907 TELEMATICS _0434308 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B153711  Telephone Sub Antenna Circuit Short to Ground  B153713  Telephone Sub Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B153711 Telephone Sub Antenna Circuit Short to Ground Navigation antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit)
·

Telephone transceiver assembly

·

Navigation antenna assembly

·

Antenna cord sub-assembly


B153713 Telephone Sub Antenna Circuit Open Navigation antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit)
·

Telephone transceiver assembly

·

Navigation antenna assembly

·

Antenna cord sub-assembly



WIRING DIAGRAM

E427067E14
5.021,1.865 6.438,2.292 1.417,0.427 10 false Telephone Transceiver Assembly 3.573,1.885 4.49,2.333 0.917,0.448 10 false Antenna Cord Sub-assembly 2.135,1.677 3.375,2.104 1.24,0.427 10 false Navigation Antenna Assembly 4.75,0.719 5.573,1.094 0.823,0.375 10 false C 4.74,1.26 5.563,1.635 0.823,0.375 10 false C 4.719,1.031 5.542,1.406 0.823,0.375 10 false 1a 4.75,0.51 5.573,0.885 0.823,0.375 10 false 1 3.271,0.719 4.094,1.094 0.823,0.375 10 false A 3.281,1.25 4.104,1.625 0.823,0.375 10 false A 3.26,1.042 4.083,1.417 0.823,0.375 10 false 4a 3.271,0.51 4.094,0.885 0.823,0.375 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
DTC B153711 or B153713 is output B



A

B

3.INSPECT NAVIGATION ANTENNA ASSEMBLY
3.INSPECT NAVIGATION ANTENNA ASSEMBLY
a.

Remove the navigation antenna assembly.

HINT:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL



b.
E356744C31
1.531,0.083 1.979,0.323 0.448,0.24 1.396,1.177 1.438,0.833 true 1.438,0.802 1.302,0.323 true 0.135,0.146 0.448,0.344 0.313,0.198 10 false *a 1.198,1.156 1.406,1.385 0.208,0.229 10 false 4a 1.188,0.156 1.396,0.385 0.208,0.229 10 false 4 1.708,0.125 1.865,0.323 0.156,0.198 10 false A
*a Component without harness connected
(Navigation Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - A-4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

4.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

4.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E427068C08
1.427,1.719 1.917,2.021 0.49,0.302 1.427,0.115 1.917,0.417 0.49,0.302 2.104,0.802 2.677,0.604 true 1.802,2.74 2.375,2.542 true 0.271,0.188 0.583,0.385 0.313,0.198 10 false *a 0.354,1.917 0.667,2.115 0.313,0.198 10 false *b 1.625,1.802 2.333,2.104 0.708,0.302 10 false C 1.635,0.208 2.344,0.51 0.708,0.302 10 false A 2.771,0.51 3.115,0.802 0.344,0.292 10 false 4a 2.438,2.427 2.781,2.719 0.344,0.292 10 false 1a
*a Front view of wire harness connector
(to Navigation Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna cord sub-assembly from the navigation antenna assembly.


b.

Disconnect the antenna cord sub-assembly from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - C-1 Always Below 1 Ω
A-4a - C-1a Always Below 1 Ω
A-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT