Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2020.07–2020.09
RM36W0E _56 Audio / Visual / Telematics _091907 TELEMATICS _0434308 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B157111  Indicator (Green) Circuit Short to Ground  B157113  Indicator (Green) Circuit Open  


DESCRIPTION

This DTC is stored when the telephone transceiver assembly detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (green) illuminates after the ignition switch is turned to ON.

If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off.

If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157111 Indicator (Green) Circuit Short to Ground Manual (SOS) switch indicator (green) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (manual (SOS) switch)

·

Harness or connector


B157113 Indicator (Green) Circuit Open Manual (SOS) switch indicator (green) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
·

Telephone transceiver assembly

·

Map light assembly (manual (SOS) switch)

·

Harness or connector



WIRING DIAGRAM

E427069E37
4.802,1.917 6.969,2.177 2.167,0.26 10 false Telephone Transceiver Assembly 4.802,1.75 6.792,1.948 1.99,0.198 10 false H85 5.177,0.792 6.5,1.135 1.323,0.344 10 false IND2 4.885,0.667 6.208,1.01 1.323,0.344 10 false 22 5.177,1.104 6.5,1.448 1.323,0.344 10 false SIG- 4.938,1.094 6.26,1.438 1.323,0.344 10 false 3 3.427,0.667 4.75,1.01 1.323,0.344 10 false 14 3.406,1.083 4.729,1.427 1.323,0.344 10 false 16 3.021,0.667 4.344,1.01 1.323,0.344 10 false IND2 2.948,1.094 4.271,1.438 1.323,0.344 10 false GND3 1.271,1.771 2.594,2.115 1.323,0.344 10 false V6 1.271,1.917 3.99,2.146 2.719,0.229 10 false Map Light Assembly (Manual (SOS) Switch)

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Turn the ignition switch to ON and wait for 10 seconds or more.


b.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are not output A
DTC B157111 or B157113 is output B



A

B

3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)
3.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (GREEN INDICATOR)
a.
E426031C18
1.448,0.188 1.906,0.448 0.458,0.26 1,1.385 0.844,1.74 true 1.427,1.365 1.813,1.729 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 0.646,1.781 1.167,2 0.521,0.219 10 false GND3 1.719,1.771 2.156,1.979 0.438,0.208 10 false IND2 1.583,0.24 1.896,0.438 0.313,0.198 10 false V6
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

HINT:

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL



b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from batteries to terminal 14 (IND2) and a negative (-) lead to terminal 16 (GND3) of the map light assembly (manual (SOS) switch) connector.


d.

Check if the manual (SOS) switch green indicator comes on.

OK:

Manual (SOS) switch green indicator illuminates.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

REPLACE MAP LIGHT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the H85 telephone transceiver assembly connector.


b.

Disconnect the V6 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-22 (IND2) - V6-14 (IND2) Always Below 1 Ω
H85-22 (IND2) or V6-14 (IND2) - Body ground Always 10 kΩ or higher
H85-3 (SIG-) - V6-16 (GND3) Always Below 1 Ω
H85-3 (SIG-) or V6-16 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL



Result:
Proceed to
NEXT



NEXT