Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2020.07–2020.09
RM36W0E _56 Audio / Visual / Telematics _091907 TELEMATICS _0434308 TELEMATICS SYSTEM(for eCall) J

TELEMATICS  TELEMATICS SYSTEM(for eCall)  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E418549E73
2.479,2.24 2.948,2.406 0.469,0.167 10 false H85 2.469,2.396 3.844,2.802 1.375,0.406 10 false Telephone Transceiver Assembly 4.563,2.615 4.938,2.823 0.375,0.208 10 false V6 4.552,2.781 6.542,3.167 1.99,0.385 10 false Map Light Assembly 4.208,0.896 4.469,1.115 0.26,0.219 10 false 9 4.198,1.698 4.51,1.938 0.313,0.24 10 false 16 4.458,0.906 4.844,1.083 0.385,0.177 10 false RRID 1.083,1.031 2.635,1.313 1.552,0.281 10 false from IGR-NO. 2 Relay 4.458,1.719 4.927,1.896 0.469,0.177 10 false GND3 4.969,2.135 6.417,2.313 1.448,0.177 10 false Manual (SOS) Switch 2.823,1.198 3.938,1.396 1.115,0.198 10 false ECU-IGR NO. 2 3.292,1.823 3.76,2 0.469,0.177 10 false SIG- 3.708,1.708 4.021,1.948 0.313,0.24 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.



HINT:

Inspect the fuses and relays related to this system before inspecting the suspected areas below.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) POWER SOURCE)
a.

Disconnect the H85 telephone transceiver assembly connector.


b.

Disconnect the V6 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H85-3 (SIG-) - V6-16 (GND3) Always Below 1 Ω
H85-3 (SIG-) or V6-16 (GND3) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V6-9 (RRID) - Body Ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
a.
E426031C21
1.469,0.177 1.906,0.427 0.438,0.25 0.885,1.74 1.01,1.365 true 2.531,1.76 2.396,1.406 true 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 0.688,1.771 1.208,1.99 0.521,0.219 10 false GND3 2.385,1.792 2.823,2 0.438,0.208 10 false RRID 1.604,0.219 1.917,0.417 0.313,0.198 10 false V6
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Apply auxiliary battery voltage to the connector.

Measurement Condition Condition Specified Condition
Auxiliary battery positive (+) → V6-9 (RRID)
Auxiliary battery negative (-) → V6-16 (GND3)
Always Manual (SOS) switch illumination comes on


c.

Check if the manual (SOS) switch illumination comes on.

OK:

The manual (SOS) switch illumination comes on.



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

3.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT