Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2020.07
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0424965 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Only Back Door cannot be Opened  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. Then, the main body ECU (multiplex network body ECU) activates the back door lock motor.

WIRING DIAGRAM

E408209E05
0.625,1.979 0.781,2.177 0.156,0.198 10 false 2 0.833,1.969 1.323,2.219 0.49,0.25 10 false ACT- 2.01,1.958 2.5,2.208 0.49,0.25 10 false ACT+ 2.177,2.51 2.406,2.708 0.229,0.198 10 false D+ 2.458,2.49 2.615,2.688 0.156,0.198 10 false 3 2.458,1.979 2.615,2.177 0.156,0.198 10 false 1 0.771,3.094 2.417,3.479 1.646,0.385 10 false Back Door Lock Assembly with Courtesy Light Switch 3.073,2.604 3.385,2.823 0.313,0.219 10 false 4E 3.073,1.875 3.385,2.094 0.313,0.219 10 false 39 3.104,2.417 3.417,2.635 0.313,0.219 10 false 2 5.354,2.479 5.844,2.729 0.49,0.25 10 false BCTY 5.365,0.323 5.854,0.573 0.49,0.25 10 false TR+ 5.01,4.302 6.646,4.667 1.635,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 1.479,5.844 1.708,6.073 0.229,0.229 10 false E 2.448,5.844 2.677,6.073 0.229,0.229 10 false UL 1.26,5.854 1.417,6.052 0.156,0.198 10 false 2 2.75,5.854 2.906,6.052 0.156,0.198 10 false 3 5.073,5.844 5.385,6.063 0.313,0.219 10 false 16 5.354,5.979 5.917,6.208 0.563,0.229 10 false TSW5 1.396,6.354 1.708,6.563 0.313,0.208 10 false Y8 1.396,6.521 2.594,6.875 1.198,0.354 10 false Back Door Opener Switch Assembly 5.375,6.49 6.24,6.667 0.865,0.177 10 false O47 5.365,6.677 6.896,7.063 1.531,0.385 10 false Certification ECU (Smart Key ECU Assembly)*2 0.667,7.417 2.823,7.677 2.156,0.26 10 false : CAN Communication Line 4.688,7.417 6.688,7.615 2,0.198 10 false *2: w/ Entry and Start System 2.542,7.417 4.604,7.604 2.063,0.188 10 false *1: w/o Entry and Start System 4.26,5.844 4.583,6.052 0.323,0.208 10 false *2 5.365,3.781 6.094,4.063 0.729,0.281 10 false BDSU*1 4.25,3.781 4.563,4 0.313,0.219 10 false *1 3.354,2.927 4.792,3.333 1.438,0.406 10 false Power Distribution Box Assembly 5.021,0.479 5.333,0.698 0.313,0.219 10 false MB 5.083,2.417 5.396,2.635 0.313,0.219 10 false 19 5.094,0.292 5.406,0.51 0.313,0.219 10 false 5 5.031,3.896 5.344,4.115 0.313,0.219 10 false H4 5.021,3.698 5.333,3.917 0.313,0.219 10 false 19 5.031,2.604 5.344,2.823 0.313,0.219 10 false MB 0.771,2.927 1.083,3.146 0.313,0.219 10 false Y7 3.906,1.292 4.792,1.469 0.885,0.177 10 false DOOR BACK 6.646,0.938 6.979,1.104 0.333,0.167 10 false IC 6.667,2.5 7,2.667 0.333,0.167 10 false IC 6.677,3.792 7.01,3.958 0.333,0.167 10 false IC 3.073,2.083 3.385,2.302 0.313,0.219 10 false 4E 2.333,1 2.646,1.219 0.313,0.219 10 false 4B 2.333,0.781 2.646,1 0.313,0.219 10 false 36 2.344,0.479 2.656,0.698 0.313,0.219 10 false 4F 2.375,0.271 2.688,0.49 0.313,0.219 10 false 1 2.854,0.615 3.729,0.844 0.875,0.229 10 false DOOR BACK 0.302,0.458 1.708,0.698 1.406,0.24 10 false from Auxiliary Battery 6.271,1.927 6.521,2.104 0.25,0.177 10 false +B 6.281,3.208 6.531,3.406 0.25,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*

*: w/ Entry and Start System

·

The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (Trunk and Back-Door Open)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display
Trunk Lid / Back Door Open
50004 449 15
OK:

The back door lock assembly with courtesy light switch unlatches when ON is selected.


Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Trunk Lid / Back Door Open Back door lock motor OFF/ON -

Result:
Result Proceed to
OK (for HV Model with Entry Function) A
OK (for Gasoline Model with Entry Function) B
OK (w/o Entry Function) C
NG D



A

B

C

2.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY

D

4.INSPECT BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH
2.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the Y8 back door opener switch assembly connector.


b.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y8-3 (UL) - H4-19 (BDSU) Always Below 1 Ω
Y8-2 (E) - Body ground Always Below 1 Ω
Y8-3 (UL) or H4-19 (BDSU) - Other terminals and body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)
a.

Disconnect the Y7 back door lock assembly with courtesy light switch connector.


b.

Disconnect the 4E power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y7-1 (ACT+) - 4E-39 Always Below 1 Ω
Y7-3 (D+) - 4E-2 Always Below 1 Ω
Y7-2 (ACT-) - Body ground Always Below 1 Ω
Y7-1 (ACT+) or 4E-39 - Body ground Always 10 kΩ or higher
Y7-3 (D+) or 4E-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E436390C02
1.5,0.25 2,0.5 0.5,0.25 5,0.5 5.5,0.75 0.5,0.25 6.365,1.396 6.115,1.396 6.115,1.396 5.865,1 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 5.177,0.563 5.521,0.792 0.344,0.229 10 false MB 6.427,1.333 6.823,1.563 0.396,0.229 10 false BCTY 1.688,0.323 2.031,0.552 0.344,0.229 10 false 4E
*a Component without harness connected
(Power Distribution Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
MB-19 (BCTY) - 4E-2 Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BATTERY AND BODY GROUND)

B

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

C

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the power distribution box assembly connectors.

E433222C01
1.542,0.219 1.875,0.458 0.333,0.24 5.021,0.188 5.354,0.427 0.333,0.24 5.104,0.229 5.417,0.427 0.313,0.198 10 false 4B 1.625,0.26 1.938,0.458 0.313,0.198 10 false 4F 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4F-1 - Body ground Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4B-36 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK POWER DISTRIBUTION BOX ASSEMBLY (DOOR BACK RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK POWER DISTRIBUTION BOX ASSEMBLY (DOOR BACK RELAY)
a.

Remove the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E433223C01
1.969,1.813 2.385,2.063 0.417,0.25 1.979,0.146 2.385,0.396 0.406,0.25 5.302,0.094 5.688,0.344 0.385,0.25 5.417,1.5 5.802,1.74 0.385,0.24 5.531,1.542 5.844,1.74 0.313,0.198 10 false 4F 2.083,1.854 2.396,2.052 0.313,0.198 10 false MB 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a 2.094,0.188 2.406,0.385 0.313,0.198 10 false 4E 5.417,0.135 5.729,0.333 0.313,0.198 10 false 4B
*a Front view of wire harness connector
(to Power Distribution Box Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
4B-36 - 4E-39 Auxiliary battery voltage applied between 4F-1 and MB-5 (TR+) 10 kΩ or higher
4B-36 - 4E-39 Auxiliary battery voltage not applied between 4F-1 and MB-5 (TR+) Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4E-39 - Auxiliary battery negative (-) terminal Auxiliary battery voltage applied between 4F-1 and MB-5 (TR+) 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

D

REPLACE POWER DISTRIBUTION BOX ASSEMBLY