| Power source mode does not change to on (IG) or on (ACC)
|
Entry and start system (for Entry Function)
|
|
| Affected by wave interference
|
| Transmitter battery
|
| Electrical key transmitter sub-assembly
|
| No. 1 indoor electrical key antenna assembly (front floor)
|
| No. 2 indoor electrical key antenna assembly (rear floor)
|
| Engine switch
|
| Wire harness or connector
|
| Power distribution box assembly
|
| Certification ECU (Smart key ECU assembly)
|
| Power source mode does not change to on (IG)
|
Wire harness or connector
|
|
Relay
- IGR NO. 1 relay
- IGR NO. 2 relay
- IGP relay
|
| Power distribution box assembly
|
| Certification ECU (Smart key ECU assembly)
|
| Power source mode does not change to on (ACC)
|
Wire harness or connector
|
|
Relay
- ACC relay
|
| Power distribution box assembly
|
| Certification ECU (Smart key ECU assembly)
|
| Engine does not start
|
Transmitter battery
|
|
| Affected by wave interference
|
| SFI system
|
| Steering lock function
|
| Immobiliser function
|
| Wire harness or connector
|
| ST NO. 1 fuse
|
| ST relay
|
| Clutch switch assembly*1
|
| Park/neutral position switch*2
|
| Electrical key transmitter sub-assembly
|
| Stop light switch assembly*2
|
| Certification ECU (Smart key ECU assembly)
|
| New key cannot be registered
|
LIN communication system
|
|
| Meter / gauge system
|
| Reregistration
|
| Electrical key transmitter sub-assembly
|
| Steering lock ECU (Steering lock actuator or upper bracket assembly)
|
| ID code box (Immobiliser code ECU)*3
|
| Certification ECU (Smart key ECU assembly)
|
| Additional key cannot be registered
|
Steering lock function
|
|
| Reregistration
|
| Electrical key transmitter sub-assembly
|
| ID code box (Immobiliser code ECU)*3
|
| Certification ECU (Smart key ECU assembly)
|
| New key registration warning message is not displayed
|
Lighting system (int)
|
|
| Meter / gauge system
|
| Certification ECU (Smart key ECU assembly)
|
| Unable to unlock steering wheel (Engine cannot start)
|
Wire harness or connector
|
|
| Steering lock ECU (Steering lock actuator or upper bracket assembly)
|
| ID code box (Immobiliser code ECU)*3
|
| Certification ECU (Smart key ECU assembly)
|
| Steering lock does not lock
|
Lighting system (int)
|
|
| Wire harness or connector
|
| Steering lock ECU (Steering lock actuator or upper bracket assembly)
|
| ID code box (Immobiliser code ECU)*3
|
| Certification ECU (Smart key ECU assembly)
|
| Security indicator light does not blink
|
Wire harness or connector
|
|
| Security indicator light (Combination meter assembly)
|
| Certification ECU (Smart key ECU assembly)
|
| Immobiliser system does not operate properly
|
Communication ID registration was defective
|
|
| Wire harness or connector
|
| ID code box (Immobiliser code ECU)*3
|
| ECM
|
| System malfunction message is displayed on the multi-information display
|
Entry and start system (for Entry Function)
|
|
| Entry and start system (for Start Function)
|
| Steering lock ECU (Steering lock actuator or upper bracket assembly)
|
| Certification ECU (Smart key ECU assembly)
|
| Park/neutral position switch*2
|
| Clutch start switch assembly*1
|
| Electronically controlled brake system
|