The steering lock ECU (steering lock actuator or upper bracket assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little, as is done for a vehicle with a mechanical key, to change the position of the lock hole.
| Problem Symptom | Data List and Active Test |
|---|---|
| Steering Lock does not Lock | Entry&Start
·
Steering Lock Request Receive ·
L Code Check ·
S Code Check*1 Main Body
·
FR Door Courtesy Switch Status ·
FL Door Courtesy Switch Status ·
RR Door Courtesy Switch Status ·
RL Door Courtesy Switch Status Power Source Control
·
Shift P Signal*2 |
*1: for TMMF Made
*2: for CVT
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Perform either of the following operations to lock/unlock the steering:
To unlock the steering, carry the electrical key transmitter sub-assembly and turn the ignition switch to ACC or ON.
To lock the steering, turn the ignition switch off with the shift lever in P (for CVT), and then open a door.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.
After performing repairs, confirm that the problem does not recur.
Inspect the fuses for circuits related to this system before performing the following procedure.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Lock Request Receive | Status of steering lock command from certification ECU (smart key ECU assembly) | OK or NG | for CVT:
OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and ignition switch off) NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and ignition switch off) for Manual Transaxle:
OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with ignition switch off) NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with ignition switch off) |
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Steering Lock Request Receive |
The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the ignition switch from ON to ACC or off and opening a door with the shift lever in P (for CVT), and OK is displayed on the GTS screen.
| Result | Proceed to |
|---|---|
| OK (for TMC Made) | A |
| OK (for TMMF Made) | B |
| NG | C |
A
B
C
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | for TMC Made:
Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) for TMMF Made:
Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) |
OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
for TMC Made:
·
The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). for TMMF Made:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
Reasons for verification failure:
The steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
*1: for TMC Made
*2: for TMMF Made
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMC Made) | B |
| NG (for TMMF Made) | C |
A
B
C
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
| *a | Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H71-1 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, check for looseness in the ground cable connection.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H71-7 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | H71-3 (IGE) - H71-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition | Steering lock motor operating when all conditions met, and then door opened:
·
Shift lever in P*1 ·
Steering unlocked ·
Ignition switch turned off |
*1: for CVT
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H71-3 (IGE) - H46-24 (SLR+) | Always | Below 1 Ω |
| H71-3 (IGE) or H46-24 (SLR+) - Other terminals and body ground | Always | 10 kΩ or higher |
Reconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Reconnect the H46 certification ECU (smart key ECU assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H71-3 (IGE) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY
Refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY
Refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| S Code Check | S code verification result | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| S Code Check |
OK is displayed on the GTS.
Reasons for verification failure:
The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.
Refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| S Code Check | S code verification result | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| S Code Check |
OK is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, check the following main body ECU (multiplex network body ECU) Data List item by opening and closing the each door to confirm the state of the each door courtesy light switch assembly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy Switch Status | Front door RH courtesy light switch signal | OFF or ON | OFF: Front door RH closed
ON: Front door RH open |
- |
| FL Door Courtesy Switch Status | Front door LH courtesy light switch signal | OFF or ON | OFF: Front door LH closed
ON: Front door LH open |
- |
| RR Door Courtesy Switch Status | Rear door RH courtesy light switch signal | OFF or ON | OFF: Rear door RH closed
ON: Rear door RH open |
- |
| RL Door Courtesy Switch Status | Rear door LH courtesy light switch signal | OFF or ON | OFF: Rear door LH closed
ON: Rear door LH open |
- |
| Tester Display |
|---|
| FR Door Courtesy Switch Status |
| FL Door Courtesy Switch Status |
| RR Door Courtesy Switch Status |
| RL Door Courtesy Switch Status |
The Data List item changes in accordance with the opening and closing of the each door.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Front Door Courtesy Switch Circuit
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Rear Door Courtesy Switch Circuit
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for CVT | A |
| for Manual Transaxle | B |
A
B
Move the shift lever to P.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift P Signal | Shift position P | OFF or ON | OFF: Shift lever not in P
ON: Shift lever in P |
·
Use this item to determine if the shift position switch is malfunctioning. ·
The engine cannot be started when this item is OFF. |
| Tester Display |
|---|
| Shift P Signal |
ON is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.
Refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Lock Request Receive | Status of steering lock command from certification ECU (smart key ECU assembly) | OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and ignition switch off) |
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Steering Lock Request Receive |
Within 10 seconds after any of the doors is opened with shift lever in P and ignition switch off, the Data List item changes to "OK".
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMC Made) | B |
| NG (for TMMF Made) | C |
A
B
C
Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY
Refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Lock Request Receive | Status of steering lock command from certification ECU (smart key ECU assembly) | OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and ignition switch off) |
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Steering Lock Request Receive |
Within 10 seconds after any of the doors is opened with shift lever in P and ignition switch off, the Data List item changes to "OK".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H46-14 (P) - Body ground | Shift lever in P → Shift lever not in P | 9 V or higher → 2.76 V or less |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Disconnect the H20 shift lock control unit assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H46-14 (P) - H20-3 (P2) | Always | Below 1 Ω |
| H46-14 (P) or H20-3 (P2) - Other terminals and body ground | Always | 10 kΩ or higher |
Reconnect the H46 certification ECU (smart key ECU assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H46-14 (P) - Body ground | Shift lever in P | 9 V or higher |
| Result | Proceed to |
|---|---|
| OK (for TMC Made) | A |
| OK (for TMMF Made) | B |
| NG | C |
A
B
C
Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.
Refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Lock Request Receive | Status of steering lock command from certification ECU (smart key ECU assembly) | OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with ignition switch off) |
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Steering Lock Request Receive |
Within 10 seconds after any of the doors is opened with ignition switch off, the Data List item changes to "OK".
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMC Made) | B |
| NG (for TMMF Made) | C |
A
B
C
Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.
Refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Lock Request Receive | Status of steering lock command from certification ECU (smart key ECU assembly) | OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with ignition switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with ignition switch off) |
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Steering Lock Request Receive |
Within 10 seconds after any of the doors is opened with ignition switch off, the Data List item changes to "OK".
| Proceed to |
|---|
| OK |
| NG |
OK
NG