Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function, Gasoline Model) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424991 ENTRY AND START SYSTEM(for Entry Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function, Gasoline Model)  B27A113  Driver Side Electrical Antenna Circuit Open  


DESCRIPTION

for LHD

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly LH (electrical key antenna) at intervals of 0.25 seconds. For the front door outside handle assembly LH (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 0.25 seconds. DTC B27A113 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly LH (electrical key antenna) (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).


for RHD

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door handle assembly outside RH (electrical key antenna) at intervals of 0.25 seconds. For the front door handle assembly outside RH (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 0.25 seconds. DTC B27A113 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and front door handle assembly outside RH (electrical key antenna) (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A113 Driver Side Electrical Antenna Circuit Open
for LHD:

An open is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly LH (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).


for RHD:

An open is detected in the circuit between the certification ECU (smart key ECU assembly) and front door handle assembly outside RH (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).


for LHD:
·

Certification ECU (smart key ECU assembly)

·

Front door outside handle assembly LH

·

Harness or connector


for LHD:
·

Certification ECU (smart key ECU assembly)

·

Front door handle assembly outside RH

·

Harness or connector


DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for driver door -

Related Data List and Active Test
DTC No. Data List and Active Test
B27A113 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B510754E50
1.323,0.771 1.719,0.948 0.396,0.177 10 false ANT1 1.313,1.917 1.708,2.083 0.396,0.167 10 false ANT2 4.938,0.885 5.76,1.146 0.823,0.26 10 false H46 4.948,2.021 6.073,2.292 1.125,0.271 10 false H46 5.323,0.771 5.719,0.948 0.396,0.177 10 false CLG1 5.323,1.906 5.719,2.083 0.396,0.177 10 false CG1B 5.844,1.375 6.052,1.542 0.208,0.167 10 false IC 6.281,2.01 6.438,2.177 0.156,0.167 10 false E 6.5,2.021 6.875,2.208 0.375,0.188 10 false H46 1.802,0.792 1.927,0.958 0.125,0.167 10 false 4 1.76,1.917 1.885,2.083 0.125,0.167 10 false 6 4.99,0.688 5.208,0.865 0.219,0.177 10 false 16 4.979,1.833 5.198,2.01 0.219,0.177 10 false 15 0.542,2.708 2.25,3.073 1.708,0.365 10 false Front Door Outside Handle Assembly LH 0.542,2.542 0.854,2.708 0.313,0.167 10 false L4 5.01,2.573 6.542,3.25 1.531,0.677 10 false Certification ECU (Smart Key ECU Assembly) 6.542,1.813 6.76,1.99 0.219,0.177 10 false 29 0.104,0.083 1.573,0.323 1.469,0.24 12 false for LHD:

B510754E51
1.323,0.771 1.719,0.948 0.396,0.177 10 false ANT1 1.313,1.917 1.708,2.083 0.396,0.167 10 false ANT2 4.938,0.885 5.76,1.146 0.823,0.26 10 false H46 4.948,2.021 6.073,2.292 1.125,0.271 10 false H46 5.323,0.771 5.719,0.948 0.396,0.177 10 false CLG1 5.323,1.906 5.719,2.083 0.396,0.177 10 false CG1B 5.844,1.375 6.052,1.542 0.208,0.167 10 false IC 6.281,2.01 6.438,2.177 0.156,0.167 10 false E 6.5,2.021 6.875,2.208 0.375,0.188 10 false H46 1.802,0.792 1.927,0.958 0.125,0.167 10 false 4 1.76,1.917 1.885,2.083 0.125,0.167 10 false 6 4.99,0.688 5.208,0.865 0.219,0.177 10 false 16 4.979,1.833 5.198,2.01 0.219,0.177 10 false 15 0.573,2.719 2.219,3.198 1.646,0.479 10 false Front Door Outside Handle Assembly RH 0.583,2.552 0.896,2.719 0.313,0.167 10 false K4 5.01,2.573 6.542,3.25 1.531,0.677 10 false Certification ECU (Smart Key ECU Assembly) 6.542,1.813 6.76,1.99 0.219,0.177 10 false 29 0.094,0.115 1.563,0.354 1.469,0.24 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK CONNECTOR CONNECTION

B

5.CHECK CONNECTOR CONNECTION
2.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly LH.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)

Pre-procedure1

a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L4 front door outside handle assembly LH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - L4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - L4-6 (ANT2) Always Below 1 Ω



Post-procedure1

d.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)
B574612C03
4.76,0.354 5.156,0.583 0.396,0.229 5.344,1.969 4.802,1.073 true 4.5,1.99 4.719,1.073 true 4.063,1.938 4.583,1.167 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 4.844,0.406 5.156,0.604 0.313,0.198 10 false H46 0.76,2.604 1.073,2.802 0.313,0.198 10 false *b 4.104,2.583 4.417,2.781 0.313,0.198 10 false *c 4.365,2 4.896,2.25 0.531,0.25 10 false CLG1 5.208,2.01 5.74,2.26 0.531,0.25 10 false CG1B 4,1.969 4.292,2.177 0.292,0.208 10 false E 0.76,3.365 1.292,3.615 0.531,0.25 10 false GND 3.844,3.354 4.375,3.604 0.531,0.25 10 false GND 3.844,5.333 4.375,5.583 0.531,0.25 10 false GND 0.771,5.333 1.302,5.583 0.531,0.25 10 false GND 0.781,4.656 1.094,4.854 0.313,0.198 10 false *d 4.063,4.615 4.375,4.813 0.313,0.198 10 false *e
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Waveform 2 *d Waveform 3
*e Waveform 4 - -


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
H46-16 (CLG1) - H46-29 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)
H46-15 (CG1B) - H46-29 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 3)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 4)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>OPERATION CHECK



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door handle assembly outside RH.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)

NG

CONNECT CONNECTORS PROPERLY

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)

Pre-procedure1

a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K4 front door handle assembly outside RH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - K4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - K4-6 (ANT2) Always Below 1 Ω



Post-procedure1

d.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)
B574612C03
4.76,0.354 5.156,0.583 0.396,0.229 5.344,1.969 4.802,1.073 true 4.5,1.99 4.719,1.073 true 4.063,1.938 4.583,1.167 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 4.844,0.406 5.156,0.604 0.313,0.198 10 false H46 0.76,2.604 1.073,2.802 0.313,0.198 10 false *b 4.104,2.583 4.417,2.781 0.313,0.198 10 false *c 4.365,2 4.896,2.25 0.531,0.25 10 false CLG1 5.208,2.01 5.74,2.26 0.531,0.25 10 false CG1B 4,1.969 4.292,2.177 0.292,0.208 10 false E 0.76,3.365 1.292,3.615 0.531,0.25 10 false GND 3.844,3.354 4.375,3.604 0.531,0.25 10 false GND 3.844,5.333 4.375,5.583 0.531,0.25 10 false GND 0.771,5.333 1.302,5.583 0.531,0.25 10 false GND 0.781,4.656 1.094,4.854 0.313,0.198 10 false *d 4.063,4.615 4.375,4.813 0.313,0.198 10 false *e
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Waveform 2 *d Waveform 3
*e Waveform 4 - -


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
H46-16 (CLG1) - H46-29 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)
H46-15 (CG1B) - H46-29 (E) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 3)
Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 4)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>OPERATION CHECK



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)