Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2020.07–2020.09
RM36W0E _59 Vehicle Exterior _088480 DOOR / HATCH _0421652 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Door window regulator sub-assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the power switch is turned to on (IG), the servo motor standard position is recognized. -


·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67492A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B584226

Disengage the claws and clip to remove the front door lower frame bracket garnish.


Hide 74232 4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

a.
B584227

Disengage the claws and guides.


b.
B584228

Disconnect the 2 connectors to remove the multiplex network master switch assembly with front armrest base upper panel.


Hide 74231 5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

a.
B584229

Disengage the claws and guides.


b.
B584230

Disconnect the connector to remove the power window regulator switch assembly with front armrest base upper panel.


Hide 67656 6.REMOVE FRONT DOOR TRIM GARNISH

a.
B584231C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the screw.


b.

Disengage the claws to remove the front door trim garnish as shown in the illustration.


Hide 67602 7.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B584232C01
1.115,1.083 1.354,1.51 true 1.302,1.531 1.542,1.729 0.24,0.198 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disengage the claw to open the front door inside handle bezel plug.


b.
B584233

Remove the 3 screws.


c.
B584234C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Disengage the clips as shown in the illustration.


d.
B584235C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the front door trim board sub-assembly with the front door glass inner weatherstrip, front door vent seal and front door panel protector as shown in the illustration.


e.
B584236C01
2.542,0.646 2.198,1 true 2.594,1.563 2.208,1.229 true 2.615,1.49 2.844,1.688 0.229,0.198 10 true *2 2.573,0.51 2.781,0.708 0.208,0.198 10 true *1
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Disengage the guides to disconnect the front door inside locking cable assembly and front door lock remote control cable assembly to remove the front door trim board sub-assembly as shown in the illustration.


Hide 69206B 8.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B584237

Disengage the guides to remove the front door inside handle sub-assembly.


Hide 69284C 9.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B584238

Disengage the claw to remove front door inside handle bezel plug.


Hide 68172A 10.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B584239C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the front door glass inner weatherstrip with the front vent seal and front door panel protector as shown in the illustration.


Hide 67838A 11.REMOVE FRONT DOOR VENT SEAL

a.
B584240

Remove the front door vent seal from the front door glass inner weatherstrip.


Hide 67856B 12.REMOVE FRONT DOOR PANEL PROTECTOR

a.
B584241

Remove the front door panel protector from the front door glass inner weatherstrip.


Hide 86160 13.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY (w/ Front Speaker)

Hide 86262E 14.REMOVE FRONT SPEAKER COVER (w/o Front Speaker)

a.
B594330

Disconnect the connector.


b.

Remove the 3 screws and front speaker cover.


Hide 87940 15.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

·

for TMC Made:

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMC Made)>REMOVAL



Hide 67832 16.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B584242

Turn the 3 front door service hole cover clips 45° to remove it clips as shown in the illustration.


b.

Disengage the guide and clamp to separate the wire harness from the front door service hole cover.


c.
B584243

Disengage the clips to remove the front door service hole cover.


Hide 68102 18.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B584244

Remove the hole plug.


b.

for Driver Side:

i.

Connect the multiplex network master switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolts can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the multiplex network master switch assembly.



c.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolts can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the power window regulator switch assembly.



d.
B584245

Remove the 2 bolts.


e.
B584246C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



Hide 69820 19.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B584247

Disconnect the connector.


b.

Remove the 6 nuts and front door window regulator assembly.


Hide 68151C 20.REMOVE FRONT DOOR GLASS RUN

a.
B584248

Remove the front door glass run.


Hide 67404F 21.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B584249

Remove the bolt.


b.

Disengage the guide to remove the front door rear lower frame sub-assembly as shown in the illustration.


Hide 67402F 22.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B584250

Remove the 2 bolts and front door front lower frame sub-assembly.


Hide 69220 23.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.

w/ Entry and Start System:

i.
B584251C01
1.49,0.594 1.958,0.385 true 1.99,0.25 2.208,0.458 0.219,0.208 10 true *a
*a Protective Tape


Disengage the claws.


ii.

Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.



b.
B584252

Disengage the 2 claws and move the lever as shown in the illustration.


c.
B584253C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door outside handle assembly as shown in the illustration.


Hide 24.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B584254

Remove the hole plug.


b.
B584255

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Remove the front door lock cylinder assembly.


Hide 69217F 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B584256

Remove the hole plug.


b.
B584257

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Disengage the claws and guides to remove the front door outside handle cover.


Hide 69241H 26.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B584258

Disengage the claws and guide to remove the front door front outside handle pad.


Hide 69242E 27.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B584259

Disengage the guides to remove the front door outside handle rear pad.


Hide 69060A 28.REMOVE FRONT DOOR LOCK ASSEMBLY

Hide 69202A 29.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

w/ Entry and Start System:

i.
B584260

Disengage the clamp to separate the wire harness.



b.
B584261C01
0,0 0,0 false
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, loosen the screw.


c.

Disengage the guides to remove the front door outside handle frame sub-assembly as shown in the illustration.


Hide 69312 30.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B584262C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the snap to remove the front door lock open rod from the front door outside frame sub-assembly as shown in the illustration.


Hide 68210C 31.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 68620 32.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B584263

Remove the 3 bolts and front door check assembly.


Hide 67862 33.REMOVE FRONT DOOR WEATHERSTRIP

a.
B584264C01
0.24,0.125 0.594,0.375 true 0.635,0.302 0.948,0.458 0.313,0.156 10 false *a
*a Clip A


Disengage the clip A and other clips to remove the front door weatherstrip.


Hide 34.REMOVE CUSHION

a.
B584265

Disengage the claws to remove the 2 cushions.


Hide 67837B 36.REMOVE FRONT DOOR DUST PROOF SEAL (for TMMF Made)

a.
B584266

Disengage the claws to remove the 3 front door dust proof seals.


Hide 67837B 37.REMOVE FRONT DOOR DUST PROOF SEAL (for TMC Made)

a.
B584266

for Type A:

i.

Disengage the claws to remove the 3 front door dust proof seals.



b.

for Type B:

i.
B621543

Disengage the claws to remove the 2 front door dust proof seals.