Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function, Gasoline Model) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424991 ENTRY AND START SYSTEM(for Entry Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function, Gasoline Model)  Driver Side Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the driver door only, but the entry lock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the unlock sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door)).

WIRING DIAGRAM

B574791E10
0.344,2.656 2.073,3.021 1.729,0.365 10 false Front Door Outside Handle Assembly LH 0.344,2.479 0.677,2.708 0.333,0.229 10 false L4 1.771,0.771 2.01,1.01 0.24,0.24 10 false 4 1.781,1.927 2.021,2.167 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.323,1.927 1.688,2.156 0.365,0.229 10 false ANT2 5.313,0.771 5.781,1.021 0.469,0.25 10 false CLG1 5.313,1.917 5.781,2.167 0.469,0.25 10 false CG1B 5.042,0.771 5.281,1.01 0.24,0.24 10 false 16 5.031,1.917 5.271,2.156 0.24,0.24 10 false 15 5.094,2.677 6.635,3.25 1.542,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.094,2.51 5.521,2.75 0.427,0.24 10 false H46 5.854,1.438 6.323,1.698 0.469,0.26 10 false IC 0.135,0.063 1.604,0.302 1.469,0.24 12 false for LHD:

B574791E11
0.344,2.656 2.198,3.042 1.854,0.385 10 false Front Door Handle Assembly Outside RH 0.344,2.479 0.677,2.708 0.333,0.229 10 false K4 1.771,0.771 2.01,1.01 0.24,0.24 10 false 4 1.781,1.927 2.021,2.167 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.323,1.927 1.688,2.156 0.365,0.229 10 false ANT2 5.313,0.771 5.781,1.021 0.469,0.25 10 false CLG1 5.313,1.917 5.781,2.167 0.469,0.25 10 false CG1B 5.042,0.771 5.281,1.01 0.24,0.24 10 false 16 5.031,1.917 5.271,2.156 0.24,0.24 10 false 15 5.094,2.677 6.635,3.25 1.542,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.094,2.51 5.521,2.75 0.427,0.24 10 false H46 5.854,1.438 6.323,1.698 0.469,0.26 10 false IC 0.146,0.073 1.615,0.313 1.469,0.24 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

8.CHECK POWER DOOR LOCK CONTROL SYSTEM
2.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

3.CHECK ENTRY OPERATION

NG

3.CHECK ENTRY OPERATION
a.

Check that the entry unlock function.

i.
B574575C02
1.719,1.052 1.063,0.396 true 0.75,0.313 1.063,0.51 0.313,0.198 10 true *a
*a Unlock Sensor (Backside)


Turn the ignition switch off.


ii.

Open and close the driver door.


iii.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


iv.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


v.

Check that the LED of the electrical key transmitter sub-assembly blinks.


vi.

Touch the unlock sensor on the backside of the front door outside handle assembly LH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (3).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (1).




Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

4.READ VALUE USING GTS (FL DOOR LOCK POSITION SWITCH STATUS)

B

4.READ VALUE USING GTS (FL DOOR LOCK POSITION SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Lock Position Switch Status Front door LH unlock detection switch signal Lock or Unlock Lock: Front door LH locked
Unlock: Front door LH unlocked
-
Body Electrical > Main Body > Data List
Tester Display
FL Door Lock Position Switch Status
50003 449 21
OK:

The GTS display changes correctly in response to the lock/unlock operation of the driver door.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

5.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)
a.
B574575C02
1.719,1.052 1.063,0.396 true 0.75,0.313 1.063,0.51 0.313,0.198 10 true *a
*a Unlock Sensor (Backside)


Open and close the driver door.


b.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


c.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


d.

Check that the LED of the electrical key transmitter sub-assembly blinks.


e.

Read the Data List according to the display on the GTS.


f.

Touch the unlock sensor on the backside of the front door outside handle assembly LH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (b).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Unlock Sensor Driver door touch sensor (unlock sensor) OFF or ON OFF: Driver door touch sensor (unlock sensor) not touched
ON: Driver door touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Unlock Sensor
50003 440 3
OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)
6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L4 front door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - L4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - L4-6 (ANT2) Always Below 1 Ω
H46-16 (CLG1) or L4-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
H46-15 (CG1B) or L4-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the L4 front door outside handle assembly LH connector.


e.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)
a.
B574575C02
1.719,1.052 1.063,0.396 true 0.75,0.313 1.063,0.51 0.313,0.198 10 true *a
*a Unlock Sensor (Backside)


Open and close the driver door.


b.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


c.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


d.

Check that the LED of the electrical key transmitter sub-assembly blinks.


e.

Read the Data List according to the display on the GTS.


f.

Touch the unlock sensor on the backside of the front door outside handle assembly LH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (b).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Unlock Sensor Driver door touch sensor (unlock sensor) OFF or ON OFF: Driver door touch sensor (unlock sensor) not touched
ON: Driver door touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Unlock Sensor
50003 440 3
OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED SECURELY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

8.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

9.CHECK ENTRY OPERATION

NG

9.CHECK ENTRY OPERATION
a.

Check that the entry unlock function.

i.
B574574C05
1.188,1.292 1.792,1.083 true 0.958,1.167 1.156,1.396 0.198,0.229 10 true *a
*a Unlock Sensor (Backside)


Turn the ignition switch off.


ii.

Open and close the driver door.


iii.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


iv.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


v.

Check that the LED of the electrical key transmitter sub-assembly blinks.


vi.

Touch the unlock sensor on the backside of the front door handle assembly outside RH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (3).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (1).




Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

10.READ VALUE USING GTS (FR DOOR LOCK POSITION SWITCH STATUS)

B

10.READ VALUE USING GTS (FR DOOR LOCK POSITION SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Position Switch Status Front door RH unlock detection switch signal Lock or Unlock Lock: Front door RH locked
Unlock: Front door RH unlocked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Position Switch Status
50003 449 20
OK:

The GTS display changes correctly in response to the lock/unlock operation of the driver door.



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

11.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)
a.
B574574C05
1.188,1.292 1.792,1.083 true 0.958,1.167 1.156,1.396 0.198,0.229 10 true *a
*a Unlock Sensor (Backside)


Open and close the driver door.


b.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


c.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


d.

Check that the LED of the electrical key transmitter sub-assembly blinks.


e.

Read the Data List according to the display on the GTS.


f.

Touch the unlock sensor on the backside of the front door handle assembly outside RH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (b).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Unlock Sensor Driver door touch sensor (unlock sensor) OFF or ON OFF: Driver door touch sensor (unlock sensor) not touched
ON: Driver door touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Unlock Sensor
50003 440 3
OK:

The GTS display changes correctly in response to the operation of the front door handle assembly outside RH.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)
12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K4 front door handle assembly outside RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - K4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - K4-6 (ANT2) Always Below 1 Ω
H46-16 (CLG1) or K4-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
H46-15 (CG1B) or K4-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the K4 front door handle assembly outside RH connector.


e.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)
a.
B574574C05
1.188,1.292 1.792,1.083 true 0.958,1.167 1.156,1.396 0.198,0.229 10 true *a
*a Unlock Sensor (Backside)


Open and close the driver door.


b.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


c.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


d.

Check that the LED of the electrical key transmitter sub-assembly blinks.


e.

Read the Data List according to the display on the GTS.


f.

Touch the unlock sensor on the backside of the front door handle assembly outside RH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (b).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Unlock Sensor Driver door touch sensor (unlock sensor) OFF or ON OFF: Driver door touch sensor (unlock sensor) not touched
ON: Driver door touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Unlock Sensor
50003 440 3
OK:

The GTS display changes correctly in response to the operation of the front door handle assembly outside RH.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED SECURELY)

NG

REPLACE FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH