Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function, Gasoline Model) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424991 ENTRY AND START SYSTEM(for Entry Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function, Gasoline Model)  Driver Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the driver door only, the request code may not be being transmitted from the driver door or the front door outside handle assembly (for driver door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (electrical key antenna)), or there may be wave interference.

WIRING DIAGRAM

B574791E10
0.344,2.656 2.073,3.021 1.729,0.365 10 false Front Door Outside Handle Assembly LH 0.344,2.479 0.677,2.708 0.333,0.229 10 false L4 1.771,0.771 2.01,1.01 0.24,0.24 10 false 4 1.781,1.927 2.021,2.167 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.323,1.927 1.688,2.156 0.365,0.229 10 false ANT2 5.313,0.771 5.781,1.021 0.469,0.25 10 false CLG1 5.313,1.917 5.781,2.167 0.469,0.25 10 false CG1B 5.042,0.771 5.281,1.01 0.24,0.24 10 false 16 5.031,1.917 5.271,2.156 0.24,0.24 10 false 15 5.094,2.677 6.635,3.25 1.542,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.094,2.51 5.521,2.75 0.427,0.24 10 false H46 5.854,1.438 6.323,1.698 0.469,0.26 10 false IC 0.135,0.063 1.604,0.302 1.469,0.24 12 false for LHD:

B574791E11
0.344,2.656 2.198,3.042 1.854,0.385 10 false Front Door Handle Assembly Outside RH 0.344,2.479 0.677,2.708 0.333,0.229 10 false K4 1.771,0.771 2.01,1.01 0.24,0.24 10 false 4 1.781,1.927 2.021,2.167 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.323,1.927 1.688,2.156 0.365,0.229 10 false ANT2 5.313,0.771 5.781,1.021 0.469,0.25 10 false CLG1 5.313,1.917 5.781,2.167 0.469,0.25 10 false CG1B 5.042,0.771 5.281,1.01 0.24,0.24 10 false 16 5.031,1.917 5.271,2.156 0.24,0.24 10 false 15 5.094,2.677 6.635,3.25 1.542,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.094,2.51 5.521,2.75 0.427,0.24 10 false H46 5.854,1.438 6.323,1.698 0.469,0.26 10 false IC 0.146,0.073 1.615,0.313 1.469,0.24 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



HINT:
·

If the driver door entry lock and unlock functions do not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

·

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.



Body Electrical > Entry&Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 440 62

PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

15.CHECK POWER DOOR LOCK CONTROL SYSTEM
2.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

3.CHECK ENTRY OPERATION

NG

3.CHECK ENTRY OPERATION
a.

Check the operation of the entry lock and unlock functions.

i.
B574575C02
1.719,1.052 1.063,0.396 true 0.75,0.313 1.063,0.51 0.313,0.198 10 true *a
*a Unlock Sensor (Backside)


Check that the entry unlock function.

1.

Turn the ignition switch off.

2.

Open and close the driver door.

3.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.

4.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.

5.

Check that the LED of the electrical key transmitter sub-assembly blinks.

6.

Touch the unlock sensor on the backside of the front door outside handle assembly LH for 2 seconds or more.*


*: Perform this step 3 seconds or more after performing step (3).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (1).



ii.
B574577C02
1.292,1.115 0.938,0.635 true 0.604,0.521 0.917,0.719 0.313,0.198 10 true *a
*a Lock Sensor


Check that the entry lock function.

1.

Turn the ignition switch off.

2.

Open and close the driver door.

3.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.

4.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (1).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.






Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

4.CHECK WAVE ENVIRONMENT

B

4.CHECK WAVE ENVIRONMENT
a.
B574573C01
2.406,1.031 2.719,1.229 0.313,0.198 10 false *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly LH and perform an entry function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>OPERATION CHECK

HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the front door outside handle assembly LH.

·

When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly LH, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.




Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

5.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)

B

AFFECTED BY WAVE INTERFERENCE

5.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)
a.
B574575C02
1.719,1.052 1.063,0.396 true 0.75,0.313 1.063,0.51 0.313,0.198 10 true *a
*a Unlock Sensor (Backside)


Open and close the driver door.


b.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


c.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


d.

Check that the LED of the electrical key transmitter sub-assembly blinks.


e.

Read the Data List according to the display on the GTS.


f.

Touch the unlock sensor on the backside of the front door outside handle assembly LH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (b).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Unlock Sensor Driver door touch sensor (unlock sensor) OFF or ON OFF: Driver door touch sensor (unlock sensor) not touched
ON: Driver door touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Unlock Sensor
50003 440 3
OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)

NG

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)
6.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)
a.
B574577C02
1.292,1.115 0.938,0.635 true 0.604,0.521 0.917,0.719 0.313,0.198 10 true *a
*a Lock Sensor


Open and close the driver door.


b.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


c.

Read the Data List according to the display on the GTS.


d.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Lock Sensor Driver door touch sensor (lock sensor) OFF or ON OFF: Driver door touch sensor (lock sensor) not touched
ON: Driver door touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Lock Sensor
50003 440 5

Result:
Result Proceed to
The GTS display does not change correctly in response to the operation of the front door outside handle assembly LH. A
The GTS display changes correctly in response to the operation of the front door outside handle assembly LH. B



A

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)

B

11.CHECK KEY DIAGNOSTIC MODE
7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L4 front door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - L4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - L4-6 (ANT2) Always Below 1 Ω
H46-16 (CLG1) or L4-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
H46-15 (CG1B) or L4-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)
a.
B574620C18
1.552,0.323 1.896,0.552 0.344,0.229 1.375,1.854 1.573,1.354 true 2.188,1.865 1.969,1.375 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.625,0.375 1.938,0.573 0.313,0.198 10 false L4 1.146,1.938 1.646,2.271 0.5,0.333 10 false ANT2 2.104,1.927 2.583,2.188 0.479,0.26 10 false ANT1 0.135,3.24 0.448,3.438 0.313,0.198 10 false GND 0.25,2.25 0.563,2.448 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Front Door Outside Handle Assembly LH)
*b Waveform 1


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
L4-4 (ANT1) - L4-6 (ANT2) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

9.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
a.

Replace the front door outside handle assembly LH with a new one or the front door handle assembly outside RH if it is functioning properly.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

10.CHECK ENTRY OPERATION
10.CHECK ENTRY OPERATION

Result:
Result Proceed to
Entry function operates normally A
Entry function does not operate normally B



A

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 440 2541

b.

Select either channel 1 or channel 2 and perform key diagnostic mode inspection for each channel.

i.
B574573C01
2.406,1.031 2.719,1.229 0.313,0.198 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly LH, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.





Result:
Result Proceed to
Wireless buzzer does not sound A
Wireless buzzer sounds B



A

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L4 front door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - L4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - L4-6 (ANT2) Always Below 1 Ω
H46-16 (CLG1) or L4-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
H46-15 (CG1B) or L4-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)
a.
B574620C18
1.552,0.323 1.896,0.552 0.344,0.229 1.375,1.854 1.573,1.354 true 2.188,1.865 1.969,1.375 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.625,0.375 1.938,0.573 0.313,0.198 10 false L4 1.146,1.938 1.646,2.271 0.5,0.333 10 false ANT2 2.104,1.927 2.583,2.188 0.479,0.26 10 false ANT1 0.135,3.24 0.448,3.438 0.313,0.198 10 false GND 0.25,2.25 0.563,2.448 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Front Door Outside Handle Assembly LH)
*b Waveform 1


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
L4-4 (ANT1) - L4-6 (ANT2) Procedure:
1.

Igniton switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

14.CHECK ENTRY OPERATION

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.CHECK ENTRY OPERATION
a.

Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

15.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

16.CHECK ENTRY OPERATION

NG

16.CHECK ENTRY OPERATION
a.

Check the operation of the entry lock and unlock functions.

i.
B574574C05
1.188,1.292 1.792,1.083 true 0.958,1.167 1.156,1.396 0.198,0.229 10 true *a
*a Unlock Sensor (Backside)


Check that the entry unlock function.

1.

Turn the ignition switch off.

2.

Open and close the driver door.

3.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.

4.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.

5.

Check that the LED of the electrical key transmitter sub-assembly blinks.

6.

Touch the unlock sensor on the backside of the front door handle assembly outside RH for 2 seconds or more.*


*: Perform this step 3 seconds or more after performing step (3).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (1).



ii.
B574576C05
2.021,1.115 2.438,0.698 true 2.49,0.583 2.688,0.771 0.198,0.188 10 true *a
*a Lock Sensor


Check that the entry lock function.

1.

Turn the ignition switch off.

2.

Open and close the driver door.

3.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.

4.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (1).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.






Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

17.CHECK WAVE ENVIRONMENT

B

17.CHECK WAVE ENVIRONMENT
a.
B574572C02
1.302,1.031 1.615,1.188 0.313,0.156 10 false *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door handle assembly outside RH and perform an entry function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>OPERATION CHECK

HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the front door handle assembly outside RH.

·

When the electrical key transmitter sub-assembly is brought near the front door handle assembly outside RH, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.




Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

18.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)

B

AFFECTED BY WAVE INTERFERENCE

18.READ VALUE USING GTS (DRIVER SIDE UNLOCK SENSOR)
a.
B574574C05
1.188,1.292 1.792,1.083 true 0.958,1.167 1.156,1.396 0.198,0.229 10 true *a
*a Unlock Sensor (Backside)


Open and close the driver door.


b.

With the electrical key transmitter sub-assembly outside of the vehicle, press the lock switch of the electrical key transmitter sub-assembly to lock all of the doors.


c.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


d.

Check that the LED of the electrical key transmitter sub-assembly blinks.


e.

Read the Data List according to the display on the GTS.


f.

Touch the unlock sensor on the backside of the front door handle assembly outside RH for 2 seconds or more.*

*: Perform this step 3 seconds or more after performing step (b).


HINT:

When checking the operation of the unlock sensor again, make sure to perform the procedure from step (a).


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Unlock Sensor Driver door touch sensor (unlock sensor) OFF or ON OFF: Driver door touch sensor (unlock sensor) not touched
ON: Driver door touch sensor (unlock sensor) touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Unlock Sensor
50003 440 3
OK:

The GTS display changes correctly in response to the operation of the front door handle assembly outside RH.



Result:
Proceed to
OK
NG



OK

19.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)

NG

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)
19.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)
a.
B574576C05
2.021,1.115 2.438,0.698 true 2.49,0.583 2.688,0.771 0.198,0.188 10 true *a
*a Lock Sensor


Open and close the driver door.


b.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


c.

Read the Data List according to the display on the GTS.


d.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Lock Sensor Driver door touch sensor (lock sensor) OFF or ON OFF: Driver door touch sensor (lock sensor) not touched
ON: Driver door touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Lock Sensor
50003 440 5

Result:
Result Proceed to
The GTS display does not change correctly in response to the operation of the front door handle assembly outside RH. A
The GTS display changes correctly in response to the operation of the front door handle assembly outside RH. B



A

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)

B

24.CHECK KEY DIAGNOSTIC MODE
20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K4 front door handle assembly outside RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - K4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - K4-6 (ANT2) Always Below 1 Ω
H46-16 (CLG1) or K4-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
H46-15 (CG1B) or K4-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

21.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)
a.
B574620C03
1.552,0.323 1.896,0.552 0.344,0.229 1.375,1.854 1.573,1.354 true 2.188,1.865 1.969,1.375 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.625,0.375 1.938,0.573 0.313,0.198 10 false K4 1.146,1.938 1.646,2.271 0.5,0.333 10 false ANT2 2.104,1.927 2.583,2.188 0.479,0.26 10 false ANT1 0.135,3.25 0.448,3.448 0.313,0.198 10 false GND 0.25,2.25 0.563,2.448 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Front Door Handle Assembly Outside RH)
*b Waveform 1


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
K4-4 (ANT1) - K4-6 (ANT2) Procedure:
1.

Ignition switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

22.REPLACE FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

22.REPLACE FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH
a.

Replace the front door handle assembly outside RH with a new one or the front door outside handle assembly LH if it is functioning properly.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

23.CHECK ENTRY OPERATION
23.CHECK ENTRY OPERATION

Result:
Result Proceed to
Entry function operates normally A
Entry function does not operate normally B



A

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) WAS DEFECTIVE)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

24.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 440 2541

b.

Select either channel 1 or channel 2 and perform key diagnostic mode inspection for each channel.

i.
B574572C02
1.302,1.031 1.615,1.188 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door handle assembly outside RH, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.





Result:
Result Proceed to
Wireless buzzer does not sound A
Wireless buzzer sounds B



A

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K4 front door handle assembly outside RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - K4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - K4-6 (ANT2) Always Below 1 Ω
H46-16 (CLG1) or K4-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
H46-15 (CG1B) or K4-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

26.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER DOOR ELECTRICAL KEY ANTENNA)
a.
B574620C04
1.552,0.323 1.896,0.552 0.344,0.229 1.375,1.854 1.573,1.354 true 2.188,1.865 1.969,1.375 true 0.219,0.188 0.531,0.385 0.313,0.198 10 false *a 1.625,0.375 1.938,0.573 0.313,0.198 10 false K4 1.146,1.938 1.646,2.271 0.5,0.333 10 false ANT2 2.104,1.927 2.583,2.188 0.479,0.26 10 false ANT1 0.125,3.25 0.438,3.448 0.313,0.198 10 false GND 0.25,2.25 0.563,2.448 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Front Door Handle Assembly Outside RH)
*b Waveform 1


Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
K4-4 (ANT1) - K4-6 (ANT2) Procedure:
1.

Igniton switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>OPERATION CHECK


Result:
Proceed to
OK
NG



OK

27.CHECK ENTRY OPERATION

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

27.CHECK ENTRY OPERATION
a.

Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

REPLACE FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)