Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function, HV Model) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424971 ENTRY AND START SYSTEM(for Entry Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function, HV Model)  Driver Side Door Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the driver door only, but the entry unlock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the lock sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly LH*1 or front door handle assembly outside RH*2).

*1: for LHD

*2: for RHD


WIRING DIAGRAM

B574791E10
0.344,2.656 2.073,3.021 1.729,0.365 10 false Front Door Outside Handle Assembly LH 0.344,2.479 0.677,2.708 0.333,0.229 10 false L4 1.771,0.771 2.01,1.01 0.24,0.24 10 false 4 1.781,1.927 2.021,2.167 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.323,1.927 1.688,2.156 0.365,0.229 10 false ANT2 5.313,0.771 5.781,1.021 0.469,0.25 10 false CLG1 5.313,1.917 5.781,2.167 0.469,0.25 10 false CG1B 5.042,0.771 5.281,1.01 0.24,0.24 10 false 16 5.031,1.917 5.271,2.156 0.24,0.24 10 false 15 5.094,2.677 6.635,3.25 1.542,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.094,2.51 5.521,2.75 0.427,0.24 10 false H46 5.854,1.438 6.323,1.698 0.469,0.26 10 false IC 0.135,0.063 1.604,0.302 1.469,0.24 12 false for LHD:

B574791E11
0.344,2.656 2.198,3.042 1.854,0.385 10 false Front Door Handle Assembly Outside RH 0.344,2.479 0.677,2.708 0.333,0.229 10 false K4 1.771,0.771 2.01,1.01 0.24,0.24 10 false 4 1.781,1.927 2.021,2.167 0.24,0.24 10 false 6 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.323,1.927 1.688,2.156 0.365,0.229 10 false ANT2 5.313,0.771 5.781,1.021 0.469,0.25 10 false CLG1 5.313,1.917 5.781,2.167 0.469,0.25 10 false CG1B 5.042,0.771 5.281,1.01 0.24,0.24 10 false 16 5.031,1.917 5.271,2.156 0.24,0.24 10 false 15 5.094,2.677 6.635,3.25 1.542,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.094,2.51 5.521,2.75 0.427,0.24 10 false H46 5.854,1.438 6.323,1.698 0.469,0.26 10 false IC 0.146,0.073 1.615,0.313 1.469,0.24 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

7.CHECK POWER DOOR LOCK CONTROL SYSTEM
2.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

3.CHECK ENTRY OPERATION

NG

3.CHECK ENTRY OPERATION
a.

Check that the entry lock function.

i.
B574577C02
1.292,1.115 0.938,0.635 true 0.604,0.521 0.917,0.719 0.313,0.198 10 true *a
*a Lock Sensor


Turn the ignition switch off.


ii.

Open and close the driver door.


iii.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


iv.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (1).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.





Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

4.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)

B

4.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)
a.
B574577C02
1.292,1.115 0.938,0.635 true 0.604,0.521 0.917,0.719 0.313,0.198 10 true *a
*a Lock Sensor


Open and close the driver door.


b.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


c.

Read the Data List according to the display on the GTS.


d.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Lock Sensor Driver door touch sensor (lock sensor) OFF or ON OFF: Driver door touch sensor (lock sensor) not touched
ON: Driver door touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Lock Sensor
50003 440 5
OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)
5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L4 front door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - L4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - L4-6 (ANT2) Always Below 1 Ω
H46-16 (CLG1) or L4-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
H46-15 (CG1B) or L4-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the L4 front door outside handle assembly LH connector.


e.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)
a.
B574577C02
1.292,1.115 0.938,0.635 true 0.604,0.521 0.917,0.719 0.313,0.198 10 true *a
*a Lock Sensor


Open and close the driver door.


b.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


c.

Read the Data List according to the display on the GTS.


d.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Lock Sensor Driver door touch sensor (lock sensor) OFF or ON OFF: Driver door touch sensor (lock sensor) not touched
ON: Driver door touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Lock Sensor
50003 440 5
OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly LH.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED SECURELY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

7.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

8.CHECK ENTRY OPERATION

NG

8.CHECK ENTRY OPERATION
a.

Check that the entry lock function.

i.
B574576C05
2.021,1.115 2.438,0.698 true 2.49,0.583 2.688,0.771 0.198,0.188 10 true *a
*a Lock Sensor


Turn the ignition switch off.


ii.

Open and close the driver door.


iii.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


iv.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (1).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.





Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

9.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)

B

9.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)
a.
B574576C05
2.021,1.115 2.438,0.698 true 2.49,0.583 2.688,0.771 0.198,0.188 10 true *a
*a Lock Sensor


Open and close the driver door.


b.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


c.

Read the Data List according to the display on the GTS.


d.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Lock Sensor Driver door touch sensor (lock sensor) OFF or ON OFF: Driver door touch sensor (lock sensor) not touched
ON: Driver door touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Lock Sensor
50003 440 5
OK:

The GTS display changes correctly in response to the operation of the front door handle assembly outside RH.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)
10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K4 front door handle assembly outside RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-16 (CLG1) - K4-4 (ANT1) Always Below 1 Ω
H46-15 (CG1B) - K4-6 (ANT2) Always Below 1 Ω
H46-16 (CLG1) or K4-4 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
H46-15 (CG1B) or K4-6 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the K4 front door handle assembly outside RH connector.


e.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING GTS (DRIVER SIDE LOCK SENSOR)
a.
B574576C05
2.021,1.115 2.438,0.698 true 2.49,0.583 2.688,0.771 0.198,0.188 10 true *a
*a Lock Sensor


Open and close the driver door.


b.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.


c.

Read the Data List according to the display on the GTS.


d.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.



Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Lock Sensor Driver door touch sensor (lock sensor) OFF or ON OFF: Driver door touch sensor (lock sensor) not touched
ON: Driver door touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Driver Side Lock Sensor
50003 440 5
OK:

The GTS display changes correctly in response to the operation of the front door handle assembly outside RH.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED SECURELY)

NG

REPLACE FRONT DOOR HANDLE ASSEMBLY OUTSIDE RH