Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2020.07
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0434686 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Unlock Warning Switch Circuit  


DESCRIPTION

The key unlock warning switch assembly comes on when the ignition key is inserted into the ignition key cylinder and goes off when the ignition key is removed.

WIRING DIAGRAM

B472053E56
5.417,2.063 7.083,2.438 1.667,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.833,1.552 3.177,1.76 2.344,0.208 10 false UnLock Warning Switch Assembly 5.844,1.01 6.281,1.24 0.438,0.229 10 false KSW 5.583,1.021 6.021,1.25 0.438,0.229 10 false 16 2.021,1.01 2.458,1.24 0.438,0.229 10 false 1 1.677,1.021 2.115,1.25 0.438,0.229 10 false UN+ 5.427,1.885 5.865,2.115 0.438,0.229 10 false H4 0.833,1.396 1.271,1.625 0.438,0.229 10 false H55 6.26,0.698 6.698,0.927 0.438,0.229 10 false +B 0.948,1 1.385,1.229 0.438,0.229 10 false 2 1.135,1.021 1.573,1.25 0.438,0.229 10 false UN-

PROCEDURE

1.READ VALUE USING GTS (KEY UNLOCK WARNING SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning Switch Unlock warning switch ON or OFF ON: Key inserted into ignition key cylinder
OFF: Key removed from ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning Switch
50003 449 127
OK:

When the key is in the ignition key cylinder, "ON" appears on the screen.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the H55 unlock warning switch assembly connector.


b.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H55-1 (UN+) - H4-16 (KSW) Always Below 1 Ω
H55-1 (UN+) or H4-16 (KSW) - Other terminals and body ground Always 10 kΩ or higher
H55-2 (UN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE UNLOCK WARNING SWITCH ASSEMBLY