The radio and display receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15D3 | Stereo Component Amplifier Disconnected | A device that is listed in the AVC-LAN connected device record of the master unit is missing. | ·
Stereo component amplifier assembly power source circuit ·
AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly ·
Stereo component amplifier assembly ·
Radio and display receiver assembly ·
Harness or connector |
The radio and display receiver assembly is the master unit.
Inspect the fuses for circuits related to this system before performing the following procedure.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.
| Result | Proceed to |
|---|---|
| DTC B15C3 is not output. | A |
| DTC B15C3 is output. | B |
A
B
Check that optional components (including associated wiring) which generate radio waves are not installed.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed. | A |
| Optional components (including associated wiring) are not installed. | B |
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/o Stop and Start System | A |
| w/ Stop and Start System | B |
A
B
Disconnect the H136 and H137 stereo component amplifier assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H136-3 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H136-1 (+B) - H136-3 (GND) | Ignition switch off | 11 to 14 V |
| H137-12 (ACC) - H136-3 (GND) | Ignition switch ACC | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H79 radio and display receiver assembly connector.
Disconnect the H137 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H79-5 (TX1+) - H137-8 (TX+) | Always | Below 1 Ω |
| H79-6 (TX1-) - H137-7 (TX-) | Always | Below 1 Ω |
| H79-5 (TX1+) - Body ground | Always | 10 kΩ or higher |
| H79-6 (TX1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the stereo component amplifier assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B
Disconnect the H136 and H137 stereo component amplifier assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H136-3 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H136-1 (+B) - H136-3 (GND) | Ignition switch off | 10.5 to 16 V |
| H137-12 (ACC) - H136-3 (GND) | Ignition switch ACC | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H79 radio and display receiver assembly connector.
Disconnect the H137 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H79-5 (TX1+) - H137-8 (TX+) | Always | Below 1 Ω |
| H79-6 (TX1-) - H137-7 (TX-) | Always | Below 1 Ω |
| H79-5 (TX1+) - Body ground | Always | 10 kΩ or higher |
| H79-6 (TX1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the stereo component amplifier assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| DTCs are not output | B |
A
B