Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0420500 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B278187  Steering Lock System Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B278187 Steering Lock System Missing Message No communication between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) for 10 seconds or more.
·

Certification ECU (smart key ECU assembly)

·

Steering lock ECU (steering lock actuator or upper bracket assembly)

·

Wire harness or connector



WIRING DIAGRAM

C434544E07
0.375,1.49 0.823,1.75 0.448,0.26 10 false H46 0.365,1.646 1.885,2.104 1.521,0.458 10 false Certification ECU (Smart Key ECU Assembly) 1.667,0.958 2.115,1.219 0.448,0.26 10 false LIN 2.75,1.469 3.26,1.656 0.51,0.188 10 false H71 2.75,1.656 5.427,2.188 2.677,0.531 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 3.24,3.333 3.688,3.594 0.448,0.26 10 false H67 3.24,3.521 4.823,3.948 1.583,0.427 10 false ID Code Box (Immobiliser Code ECU)*1 0.719,4.333 2.49,4.813 1.771,0.479 10 false : LIN Communication Line 3.094,2.625 3.542,2.885 0.448,0.26 10 false 2 4.844,0.719 5.063,0.896 0.219,0.177 10 false 7 1.99,0.802 2.438,1.063 0.448,0.26 10 false 8 4.438,1.125 4.792,1.313 0.354,0.188 10 false GND 3.281,2.813 3.729,3.073 0.448,0.26 10 false LIN1 0.292,3.938 2.979,4.167 2.688,0.229 10 false *1: w/ ID Code Box 3.083,0.792 3.26,0.979 0.177,0.188 10 false 5 3.292,0.969 3.74,1.229 0.448,0.26 10 false LIN 4.594,0.781 4.948,0.969 0.354,0.188 10 false B 4.823,1.021 5.042,1.198 0.219,0.177 10 false 1 5.01,0.948 5.917,1.135 0.906,0.188 10 false STAG LOCK 6.094,0.792 6.979,1.167 0.885,0.375 10 false from Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing the inspection, check that DTC B2786 or B278C is not output.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B278187 and B278588 are output A
Only DTC 278187 is output B
DTC B278187 and B278588 are not output C



A

B

3.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - AUXILIARY BATTERY AND BODY GROUND)

C

3.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H71-7 (B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o ID Code Box A
w/ ID Code Box B



A

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))

B

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-5 (LIN) - H46-8 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK LIN COMMUNICATION LINE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK LIN COMMUNICATION LINE
a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-5 (LIN) - Body ground Always Pulse generation



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H71-5 (LIN) - H46-8 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR