Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2020.07
RM36W0E _56 Audio / Visual / Telematics _088616 NAVIGATION / MULTI INFO DISPLAY _0422142 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1543  Extension Module Disconnected 2  


DESCRIPTION

If the radio and display receiver assembly cannot detect the navigation ECU for a certain period of time (90 seconds) after the ignition switch is turned to ACC and the radio and display receiver assembly confirms that the information is missing by checking past navigation ECU recognition information (registered information), this DTC will be stored.

HINT:

The Navigation system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the Navigation system will not operate normally.


DTC No. Detection Item DTC Detection Condition Trouble Area
B1543 Extension Module Disconnected 2 Navigation ECU disconnected
·

Navigation ECU

·

Radio and display receiver assembly

·

Harness or connector



HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.


WIRING DIAGRAM

E445974E01
5.854,2.823 7.052,3.438 1.198,0.615 10 false Radio and Display Receiver Assembly 5.865,2.667 6.313,2.979 0.448,0.313 10 false H123 3.542,2.646 4.698,3.177 1.156,0.531 10 false Navigation ECU 3.26,1.26 3.677,1.5 0.417,0.24 10 false H82 4.5,0.729 4.927,0.969 0.427,0.24 10 false H122 1.865,1.406 3.021,1.938 1.156,0.531 10 false ECU-DCC NO. 2 0.458,1.25 1.333,1.76 0.875,0.51 10 false from Auxiliary Battery*2 3.615,1.26 4.104,1.656 0.49,0.396 10 false +B 3.604,2.104 4.094,2.5 0.49,0.396 10 false GND 4.073,0.719 4.563,1.115 0.49,0.396 10 false US4+ 4.115,1.417 4.604,1.813 0.49,0.396 10 false US4- 4.063,2.094 4.552,2.49 0.49,0.396 10 false UGD4 6.063,0.729 6.552,1.125 0.49,0.396 10 false US4+ 6.073,1.427 6.563,1.823 0.49,0.396 10 false US4- 6.083,2.104 6.573,2.5 0.49,0.396 10 false UGD4 4.615,0.521 5.031,0.896 0.417,0.375 10 false 4 4.604,1.229 4.833,1.583 0.229,0.354 10 false 5 4.615,1.896 5.031,2.271 0.417,0.375 10 false 6 3.302,1.063 3.719,1.438 0.417,0.375 10 false 10 3.302,1.896 3.719,2.271 0.417,0.375 10 false 23 5.896,0.604 6.313,0.979 0.417,0.375 10 false 1 5.906,1.313 6.323,1.656 0.417,0.344 10 false 2 5.917,2.01 6.333,2.354 0.417,0.344 10 false 3 0.719,3.385 2.469,3.677 1.75,0.292 10 false : USB Communication Line 0.188,2.979 0.948,3.208 0.76,0.229 10 false *3: Shielded 5.229,1.667 5.458,1.833 0.229,0.167 10 false *3 4.49,1.427 4.917,1.667 0.427,0.24 10 false H122 4.5,2.094 4.927,2.333 0.427,0.24 10 false H122 3.26,2.083 3.677,2.323 0.417,0.24 10 false H82 0.073,0.344 1.438,0.75 1.365,0.406 10 false from Engine Stop and Start ECU*1 0.167,2.292 2.302,2.542 2.135,0.25 10 false *1: w/ Stop and Start System 0.167,2.635 2.563,2.906 2.396,0.271 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK MAP SCREEN
a.

Turn the ignition switch to ACC and wait for 90 seconds.


b.

Press the "MAP" switch and check that the map screen is displayed normally.


Result:
Result Proceed to
Map screen is displayed normally A
Map screen is not displayed normally B


HINT:
·

This DTC may be stored due to environmental reasons such as electrical noise or interference.

·

Clear past DTCs when the map screen is displayed normally. (Codes stored due to past environmental factors)




A

B

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

4.CHECK VEHICLE TYPE

B

4.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

5.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - AUXILIARY BATTERY AND BODY GROUND)

B

10.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - AUXILIARY BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the H82 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H82-23 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H82-10 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the H122 navigation ECU connector.


b.

Disconnect the H123 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H122-4 (US4+) - H123-1 (US4+) Always Below 1 Ω
H122-5 (US4-) - H123-2 (US4-) Always Below 1 Ω
H122-6 (UGD4) - H123-3 (UGD4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.REPLACE NAVIGATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END (NAVIGATION ECU IS DEFECTIVE)

10.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the H82 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H82-23 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H82-10 (+B) - Body ground Ignition switch off 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

NG

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the H122 navigation ECU connector.


b.

Disconnect the H123 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H122-4 (US4+) - H123-1 (US4+) Always Below 1 Ω
H122-5 (US4-) - H123-2 (US4-) Always Below 1 Ω
H122-6 (UGD4) - H123-3 (UGD4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.REPLACE NAVIGATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END (NAVIGATION ECU IS DEFECTIVE)