Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.07–2020.09
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424331 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Brake actuator assembly branch line or connector

·

Power source circuit of brake actuator assembly

·

Brake actuator assembly ground circuit

·

Brake actuator assembly



WIRING DIAGRAM

for TMC Made



E433987E02
5.417,5.75 5.875,5.948 0.458,0.198 10 false A36 5.76,0.583 6.219,0.781 0.458,0.198 10 false CANH 5.771,1.052 6.229,1.25 0.458,0.198 10 false CANL 5.76,1.906 6.219,2.104 0.458,0.198 10 false BM 5.781,3.115 6.24,3.313 0.458,0.198 10 false IGR 5.792,4.771 6.25,4.969 0.458,0.198 10 false GND2 5.51,0.5 5.969,0.698 0.458,0.198 10 false 22 5.479,0.979 5.938,1.177 0.458,0.198 10 false 10 5.479,2.438 5.938,2.635 0.458,0.198 10 false 38 5.51,3.969 5.969,4.167 0.458,0.198 10 false 25 1.844,0.469 2.302,0.667 0.458,0.198 10 false 3 1.854,0.948 2.313,1.146 0.458,0.198 10 false 9 0.302,1.385 0.76,1.583 0.458,0.198 10 false H112 0.292,1.542 3.01,1.792 2.719,0.25 10 false No. 2 Global CAN Junction Connector 3.823,2.073 5.021,2.292 1.198,0.219 10 false ABS NO. 1 3.844,2.688 5.042,2.906 1.198,0.219 10 false ABS NO. 2 5.417,5.917 7.073,6.229 1.656,0.313 10 false Brake Actuator Assembly 5.771,2.531 6.229,2.729 0.458,0.198 10 false +BS 5.479,1.813 5.938,2.01 0.458,0.198 10 false 13 5.479,3.031 5.938,3.229 0.458,0.198 10 false 12 5.792,4.094 6.25,4.292 0.458,0.198 10 false GND1 5.563,4.656 6.021,4.854 0.458,0.198 10 false 1 1.615,3.115 3.375,3.438 1.76,0.323 10 false from IGR-NO. 1 Relay 1.625,1.885 3.271,2.188 1.646,0.302 10 false from Auxiliary Battery 3.75,3.302 4.948,3.521 1.198,0.219 10 false ECU-IGR NO. 3 1.635,2.49 3.281,2.792 1.646,0.302 10 false from Auxiliary Battery

for TMMF Made


E433987E04
5.417,5.75 5.875,5.948 0.458,0.198 10 false A37 5.76,0.583 6.219,0.781 0.458,0.198 10 false CANH 5.771,1.052 6.229,1.25 0.458,0.198 10 false CANL 5.771,1.906 6.229,2.104 0.458,0.198 10 false +BM 5.781,3.115 6.24,3.313 0.458,0.198 10 false IGR 5.792,4.771 6.25,4.969 0.458,0.198 10 false GND2 5.5,0.479 5.958,0.677 0.458,0.198 10 false 11 5.479,0.948 5.938,1.146 0.458,0.198 10 false 10 5.479,2.417 5.938,2.615 0.458,0.198 10 false 25 5.49,3.969 5.948,4.167 0.458,0.198 10 false 38 1.844,0.469 2.302,0.667 0.458,0.198 10 false 3 1.854,0.948 2.313,1.146 0.458,0.198 10 false 9 0.302,1.385 0.76,1.583 0.458,0.198 10 false H112 0.292,1.542 3.01,1.792 2.719,0.25 10 false No. 2 Global CAN Junction Connector 3.823,2.073 5.021,2.292 1.198,0.219 10 false ABS NO. 1 3.844,2.688 5.042,2.906 1.198,0.219 10 false ABS NO. 2 5.417,5.917 7.073,6.229 1.656,0.313 10 false Brake Actuator Assembly 5.771,2.531 6.229,2.729 0.458,0.198 10 false +BS 5.542,1.792 6,1.99 0.458,0.198 10 false 1 5.542,3.01 6,3.208 0.458,0.198 10 false 6 5.792,4.094 6.25,4.292 0.458,0.198 10 false GND1 5.49,4.656 5.948,4.854 0.458,0.198 10 false 13 1.615,3.115 3.375,3.438 1.76,0.323 10 false from IGR-NO. 1 Relay 1.625,1.885 3.271,2.188 1.646,0.302 10 false from Auxiliary Battery 3.75,3.302 4.948,3.521 1.198,0.219 10 false ECU-IGR NO. 3 1.635,2.49 3.281,2.792 1.646,0.302 10 false from Auxiliary Battery


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)

B

4.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A36 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-22 (CANH) - A36-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-25 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A36-1 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A36-13 (BM) - Body ground Ignition switch off 11 to 14 V
A36-38 (+BS) - Body ground Ignition switch off 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS LINES (BRAKE ACTUATOR ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A37 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-11 (CANH) - A37-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-38 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A37-13 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-1 (+BM) - Body ground Ignition switch off 11 to 14 V
A37-25 (+BS) - Body ground Ignition switch off 11 to 14 V
A37-6 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)