Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for Gasoline Model TMMF Made RHD) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432228 BRAKE ACTUATOR(for Gasoline Model TMMF Made RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for Gasoline Model TMMF Made RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

*2: w/ Gasoline Particulate Filter

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking Assist Monitor System (Click here)
for 1KR-FE:

ECM


Perform Vehicle Identification Number (VIN) or frame number registration Rough idle (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
for M15A-FKS:

ECM


Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
If possible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
If impossible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)
Skid control ECU (brake actuator assembly) Update ECU security key Vehicle control history (RoB) are stored (Click here)
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55815E 4.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 7.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 9.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 10.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 11.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 12.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C436307C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C432502

Using a 10 mm union nut wrench, disconnect the brake line from the front flexible hose.


c.
C436308C01
1.365,1.656 1.594,1.354 true 2.115,1.177 2.354,1.542 true 1.938,0.875 2.458,0.531 true 1.792,0.917 1.896,0.26 true 1.021,1.01 1.427,1.052 true 1.25,0.604 1.625,0.969 true 1.219,1.635 1.479,1.833 0.26,0.198 10 true *b 2.292,1.542 2.521,1.792 0.229,0.25 10 true *a 2.5,0.396 2.729,0.604 0.229,0.208 10 true *f 1.792,0.073 2.031,0.26 0.24,0.188 10 true *e 1.01,0.448 1.219,0.656 0.208,0.208 10 true *d 0.771,0.896 1,1.083 0.229,0.188 10 true *c
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake lines.


d.
C436309

Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.


e.
C436310

Remove the bolt, 2 nuts and brake actuator with bracket from the vehicle body.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



Hide 44510 13.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C436311

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44547B 14.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.
C436312C02
2.073,1.646 2.323,1.646 false 1.938,0.573 2.198,0.573 false 2.771,0.552 2.938,0.552 false 0.417,1.396 0.417,1.646 false 0.729,1.656 0.729,1.906 false 1.5,0.24 1.76,0.24 false 3.021,0.906 3.021,1.156 false 2.969,0.49 3.177,0.688 0.208,0.198 10 false *2 2.375,1.594 2.688,1.75 0.313,0.156 10 false *3 2.948,1.177 3.26,1.333 0.313,0.156 10 false *1 0.667,1.927 0.979,2.083 0.313,0.156 10 false *1 2.219,0.5 2.531,0.656 0.313,0.156 10 false *2 0.333,1.667 0.646,1.823 0.313,0.156 10 false *2 1.313,0.167 1.625,0.323 0.313,0.156 10 false *1
*1 No. 1 Brake Actuator Case Collar
*2 Brake Actuator Bracket Cushion
*3 Brake Actuator Bracket Assembly


Remove the 3 No. 1 brake actuator case collars from the brake actuator bracket cushion.


b.

Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.